MG—375/750采煤机液压系统的污染控制

介绍了MG— 375 75 0采煤机液压系统污染危害的种类及控制方法 ,并收到了良好效果     

真空相变锅炉低排烟温度设计与低温腐蚀

真空相变锅炉是否会明显发生烟气低温腐蚀，一直众说不一。文章从锅炉发生低温腐蚀的机理人手，通过理论分析计算并通过实践检验，提出了真空相变锅炉虽然不能完全避免低温腐蚀问题，但不论排烟温度是否高于烟气露点，低温腐蚀的程度都很弱的观点；给出了真空相变锅炉沿烟气流程金属壁面的腐蚀速度与壁面温度的关系曲线，和烟气温度低于酸露点时金属壁面的腐蚀速度与壁面温度的关系曲线；同时，文章推荐真空相变锅炉的设计排烟温度取130℃左右的低排烟温度。根据上述观点设计的数百台产品已经过多年实际运行，未发现明显     

裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

SUPMAX500系统在锅炉控制系统中的应用

针对动力厂35t/h锅炉的工艺控制要求，选用SUPMAX500集散控制系统。介绍了系统的软、硬件构成及其具体实施方法。     

分置式牛津型斯特林制冷机的数值分析与实验验证

对分置式牛津型斯特林制冷机进行了数值计算 ,介绍了计算模型考虑到的众多不可逆因素。通过对计算结果与实验结果的对比 ,验证了本文数值计算的准确性 ,说明本文计算模型与数值处理方法是切实可行的     

水喷雾灭火系统在电信枢纽工程燃气锅炉房的应用

分析了燃气锅炉的火灾危险性和水喷雾用于燃气锅炉消防的灭火机理,提出了水喷雾灭火系统的设计参数的选择、系统的控制方法以及在设计中可能涉及到的问题和注意事项,并结合工程实例进行了探讨。     

Boiling: Size Distribution of Bubbles as Demanded by the Principle of Maximum Information

The principle of maximum informational entropy is used to find the probability density function for the departure radius of a bubble in boiling on a solid surface. A general relation is derived, which leads to particular expressions.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

国产螺旋槽密封在进口压缩机上的应用

介绍了国产螺旋槽密封在进口压缩机上的应用，分析了原进口机械-浮环组合密封的失效原因，叙述了改造后国产浮环螺旋槽组合密封的结构和特点。