湍流模型和网格分布对水下航行体回转水动力数值计算的影响

针对水下航行体安全操纵设计的关键环节水动力预报,用FLUENT求解不可压缩RANS方程,采用定常旋转运动坐标系,运用相对运动理论和运动叠加原理,计算RNG k-ε,可实现k-ε和SST k-ε等3种湍流模型以及不同网格分布对水下航行体做单平面回转运动所受垂向力和纵倾力矩,并与试验结果比较.结果表明在Re=11.7×106条件下,垂向力和纵倾力矩预报精度较高.该数值预报方法可行、有效,具有较好的工程实用价值.     

Review on the effect of heat exchanger tubes on flow behavior and heat/mass transfer of the bubble/slurry reactors

Bubble/Slurry bubble column reactors(BCR/SBCR) are intensively used as multiphase reactors for a wide range of application in the chemical, biochemical and petrochemical industries. Most of these applications involve complicate gas–liquid/gas–liquid–solid flow behavior and exothermic process, thus it is necessary to equip the BCR/SBCR with heat exchanger tubes to remove the heat and govern the performance of the reactor. Amounts of experimental and numerical studies have been carried out to describe the phenomena taking place in BCR/SBCRs with heat exchanger tubes. Unfortunately, little effort has been put on reviewing the experiments and simulations for examining the effect of internals on the performance and hydrodynamics of BCR/SBCR. The objective of this work is to give a state-of-the-art review of the literature on the effects of heat exchanger tubes with different types and configurations on flow behavior and heat/mass transfer, then provide adequate information and scientific basis for the design and the development of heat exchanger tubes in BCR/SBCR, ultimately provide reasonable suggestions for better comprehend the performance of different heat exchanger tubes on hydrodynamics.     

COMPARISON BETWEEN THEORETICAL FORMULA AND EXPERIMENTAL RESULTS ON BUBBLE ELECTROPHORESIS

ＣＯＭＰＡＲＩＳＯＮＢＥＴＷＥＥＮＴＨＥＯＲＥＴＩＣＡＬＦＯＲＭＵＬＡＡＮＤＥＸＰＥＲＩＭＥＮＴＡＬＲＥＳＵＬＴＳＯＮＢＵＢＢＬＥＥＬＥＣＴＲＯＰＨＯＲＥＳＩＳ￥ＸｕＪｉｒｕｎ；ＫｅｌｓａｌｌＧＨ（Ｐ．Ｏ．Ｂｏｘ１３９，ＮｏｒｔｈｅａｓｔｅｒｎＵｎｉ...     

用人工神经网络方法预测鼓泡塔气含率

A new correlation for the prediction of gas hod up in bubble columns was proposed based on an extensive experimental database set up from the literature published over last 30 years .The updated estimation method relying on artificial neural network,dimensional analysis and phenomenological approaches was used and the model prediction agreed with the experimental data with average relative error less than 10%.     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

Current problems in the modelling of chemical reactors

Modelling of chemical reactors is reviewed with an emphasis on process development and scale-up. A distinction is made between modelling of chemical kinetics, of rate processes in volume elements and of whole reactors. Examples are mainly taken from papers presented at the Sixth International Symposium on Chemical Reaction Engineering. Special attention is given to the modelling of single phase reactors, fixed beds, trickle beds, fluid beds, and gas bubble reactors.     

大液相负荷下斜孔塔板的流体力学性能

针对大液相负荷气液传质操作 ,通过冷模实验 ,重新确定了普通斜孔塔板的液体力学性能 ,并给出了新的关联式。同时基于普通正排斜孔塔板在大液量操作条件下压降大 ,泄漏和雾沫夹带严重等缺点 ,沿用梯形导向浮阀的思想 ,提出了变正排为斜排的改进方案 ,并在相同条件下对两者的液体力学性能进行初步比较。证明了斜排斜孔塔板是一种适合大液体处理量且操作弹性较宽的塔板     

PX氧化鼓泡塔反应器内的TA浓度分布

利用新建的D476鼓泡塔冷模实验装置和沉降—扩散模型对工业鼓泡塔PX氧化反应器内的TA浓度分布进行了实验和数学模拟研究。结果表明,由于PX氧化气速较大,塔内TA浓度接近均匀分布。     

垂直管内弹状气泡上升中壁面传递的实验研究

垂直管内弹状流壁面传递是诸多工业应用中需研究的重要问题之一。今用极限扩散电流技术,对弹状气泡上升时瞬时壁面剪应力和传质系数进行了测定,结果显示:当基于表观气速的Froude数FrG < 0.74时,壁面剪应力随弹状气泡和液塞的到来呈现方向相反的交替变化,壁面传质系数亦相应变化;而当FrG > 0.74时,剪应力方向一直向下,说明液膜向下流动,且弹状气泡和液塞的到来对壁面传质系数的影响很小。这说明下落液膜射流穿透了液塞段,控制了整个壁面传递过程。研究还对下落液膜区、尾迹区及液塞段的不同传递特征及机理进行了分析, 并结合气泡塔熔融结晶器中弹状气泡上升时的传热,对结晶操作条件的合理选择进行了讨论。     

Bubble Formation at a Rotating Cylindrical Surface in Cross‐Flowing Liquid

A novel method of gas sparging from a rotating cylinder is proposed, which prevents against formation of large attached gas cavities in cross‐flowing liquids including those flowing downwards. Experimental and theoretical results regarding critical rotation speed necessary to remove the attached cavity, bubble formation process and size distribution of the produced bubbles in a low viscosity system (air‐water) are presented in this study.