油滴釉制作工艺的研究

在研制氧化气氛烧制油滴黑釉器的基础上 ,探讨了影响油滴釉形成的工艺因素。通过一系列试验 ,进一步验证了油滴釉在结晶过程中主要发生了液液分相 ;釉料的化学组成是油滴晶斑形成的先决条件 ;釉层厚度、烧成制度等是决定釉面效果的重要因素 ;油滴晶斑的呈色不仅与烧成气氛有关 ,还与着色氧化物的引入有关。     

熔块中的气泡缺陷及其解决办法

分析了熔块生产中气泡缺陷产生的各种原因．提出了实际生产中的注意事项和具体的解决办法。     

MathCAD软件对塑料发泡振动的模拟

气泡膨胀过程中产生的高频振动已达到超声波范围,对聚合物中纳米粒子的分散具有很好的作用。利用MathCAD模拟了气泡振动影响因素,分析了气泡内外压差、高聚物熔体的表面张力、应力松弛时间等因素对气泡振动的影响。通过分析,对气泡振动的工艺条件提出一些参考。     

Chaos in bubbling—nonlinear analysis and modelling

In the present paper, nonlinear features and analytical results for the chaotic bubbling from a submerged orifice are described. A chain of air bubbles was produced from the single orifice of in diameter and micro-convection induced by the bubble generation was recorded using hot-probe anemometer located close to the orifice. The air flow rate was varied widely from q=100 to and the aspects of bubbling were observed by high-speed video. The nonlinear analysis is performed for the time series data of hot-probe anemometer especially in the range of q=435-. The calculated largest Lyapunov exponent shows that with increase of air volume flow rate, the time period for the process of liquid flow to lose stability becomes shorter and at high air flow rate such as , it is shorter than the time period between subsequent bubbles. To explain such chaotic behaviors of bubbling, a simple model has been proposed. The model simulates the process of interaction between the elastic bubble wall and liquid. Simulation results compared well with the analytical results of experimental data. Summarizing, it is concluded that one of the reasons for chaos appearance is the nonlinear character of interaction between an elastic bubble wall and the liquid stream.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

模拟三相流化床中颗粒尺寸对单气泡传质系数的影响

本文在模拟三相流化床中,测量了单气泡的传质系数,实验结果表明颗粒直径对气-液传质系数影响显著。颗粒直径较大时,传质系数有明显提高。     

Gas hold-up in non-newtonian solutions in a bubble column with internals

Bubble characteristics and gas hold-up were studied in a two phase (air-aqueous CMC solution) bubble column provided with helical coils and straight tubes as internals. The effects of superficial gas velocity, rheological properties, and volume fraction covered by the internals, on gas hold-up were studied. Hold-up values determined directly and by simultaneous pressure drop measurements matched well. Enhancement of gas hold-up values up to 55 per cent was achieved in systems using internals. The gas hold-up results were also compared with the values obtained from correlations reported in the literature.     

Study of Hydrodynamics,Mixing and Gas‐Liquid Mass Transfer in a Split‐Rectangular Airlift Reactor

Global hydrodynamic characteristics, liquid mixing and gas‐liquid mass transfer for a 63 L split‐rectangular airlift reactor were studied. Correlations for gas holdup and overall liquid circulation velocity were derived for the air‐water system as a function of the specific power input; these were compared to data and correlations for reactor volumes between 4.7 L and 4600 L. A partial recirculation of small bubbles in the riser was observed when U_gr > 0.03 m/s, which was attributed to the use of a single‐orifice nozzle as the gas phase distributor. The dimensionless mixing time and the overall axial dispersion coefficient were nearly constant for the range of gas flow rates studied. However, values of K_L/d_B were greater than those reported in previous studies and this is caused by the partial recirculation of the gas phase in the riser. While scale effects remain slight, the use of a gas distributor favouring this partial recirculation seems adequate for mass transfer in split‐rectangular airlift reactors.     

美国能源部的浆态床F－T合成技术

浆态床Ｆ－Ｔ合成技术是美国能源部Ｆ－Ｔ合成技术的主要开发项目。本文就浆态相Ｆ－Ｔ合成催化剂的开发、中试示范实验和浆态反应器的化工基础研究作一扼要的介绍。