电力变压器局放超声传感器及其应用

作者研制成一种带光纤的电力变压器局放超声PZT传感器.文中分析了它的灵敏度与宽频带特性,介绍了原理、结构设计、实验数据及现场成功实例.理论与实验研究表明:具有这种高灵敏传感器的超声定位系统是确定电力变压器绝缘故障部位的一种方法.     

Cure reaction for modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide

The glass‐transition temperature as a function of curing conversion for a modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide (BMI) resin was investigated at different temperature regimes and modeled using a modified Di Benedetto equation. Although the relationship between the glass‐transition temperature and conversion of the BMI system conforms to the Di Benedetto equation for α < 0.6 and at lower cure temperatures, at higher cure temperatures the results deviated significantly from the equation; thus, it was an inadequate model for the system. Fourier transform IR analysis showed that the major crosslinking reactions did not occur during cure for the modified BMI at and below 150°C. However, as the cure temperature was increased, the crosslinking reactions responsible for 3‐dimensional network structures became more dominant. At 190°C the C? N? C_stretch vibration of the uncured maleimide ring converted into succinimide rings in the curing process. Simultaneously, a decrease was observed for the absorbance bands of ? C? H_bending (maleimide). The higher cure temperatures induced a significantly faster initial crosslinking rate and also resulted in a shorter period of time after which further crosslinking was retarded, because the increase in the crosslinks also physically slowed further crosslinking activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 227–235, 2002     

片式多层电容电阻复合元件的研制

采用低温共烧陶瓷(LTCC)技术将电容、电阻元件集成在多层陶瓷基板里,构成了一种新型的片式多层复合元件,并研究了其制造工艺性能和频率特性。结果表明,片式多层电容电阻复合元件制造工艺适合批量化生产,并为片式多层LC滤波器、LTCC基板及器件的研发提供了极好的参考价值。     

单晶空心叶片用AC-2陶瓷型芯的组织和性能研究

利用扫描电镜技术和X射线衍射技术研究了AC－2氧化铝基陶瓷型芯的微观结构和相组成，并测试了该型芯的室温和高温性能，结果表明AC－2型氧化铝基陶瓷型芯的综合性能优于AC－1型芯。     

Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

一种低频 空间定向及高灵敏遥感方法研究

本文提出一种低频、空间定向及高灵敏的遥感方法。文中介绍了传感器及其二次仪表设计原理和关键技术。由作者研制的本检测系统,在空气中的定向接收灵敏度,离1米处高达120mV/μPa,比HP4905A型机的输出信噪比高8倍.     

Al2O3基耐磨陶瓷涂层的燃烧合成与应用

介绍了燃烧合成表面涂层技术的基本原理 ,开发了相应的制备工艺 ,并在此基础上研制了内覆陶瓷涂层的复合钢管、弯管及弯头。陶瓷涂层主要由α Al2 O3相、部分FeO·Al2 O3相和 3Al2 O3·2SiO2 相组成 ,采用添加剂可以有效提高熔体的流动性 ,使陶瓷的凝固和结晶过程得到进一步控制 ,有助于减少孔隙 ,提高陶瓷涂层的致密度。现场应用试验表明 ,涂层具有较好的耐磨性能 ,可使设备的使用寿命大为延长     

Dynamics of hydrated iron(II) cations in nafion polymer membranes

Mössbauer studies of Fe²⁺ in water-soaked nafion polymer membranes in the temperature range between 90 K and 250 K have been performed. Above a critical temperature (～ 180 K) the spectra exhibit both elastic narrow absorption lines and quasielastic broad lines. These spectra are typical of bounded diffusion phenomena observed by Mössbauer spectroscopy in macromolecular systems like haemoglobin, myoglobin and ferritin. Similar spectral shapes have been observed by quasielastic neutron scattering from water in nafion membranes. Within 50 K above the critical temperature the total Mössbauer absorption area decreases by an order of magnitude whereas the narrow absorption line decreases by two orders of magnitude. The results are interpreted in terms of bounded diffusive motion of the iron. Using a model based on overdamped harmonically bound Brownian motion, the essential parameters of the iron motion can be derived as a function of temperature. The iron motion most probably reflects the motion of a large Fe²⁺ complex, e.g. Fe(H₂O)²⁺₆, which is attached to the polymer side chains via the sulphonic group.     

Forecasting Capillary Characteristics for Aluminum Nitride Ceramic ― Liquid Metal Systems

A test has been devised that allows one to determine the work of adhesion and wettability in a system composed of aluminum nitride ceramics with a liquid metal without the need for experimental examination. A correlation is examined between the work of adhesion on the one hand and that criteria or others on the other that have been proposed by various researchers. Forecasts are made for the work of adhesion and wetting angle for a series of metals that have not been examined previously. An experimental check has been made on the forecast adhesion activity for some elements.     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。