多层水平气流带式干燥机的数学模型

根据干燥传质传热学原理和干燥动力学特性，建立了水平气流带式干燥机干燥过程的数学模型。该模型可以预测干燥机合理的通风道高度、带翻转最佳时间和热风风速等。为优化多层带式干燥机的结构或设计新的水平气流带式干燥机提供了理论依据。     

Process conditions affect pigment quality and yield in extracts of purple sunflower hulls

Extract of purple sunflower hulls is a potential red food colorant; however, suitable process conditions must still be identified. Selected process variables were studied using bench-scale units to prepare, clarify, concentrate and spray dry extracts. Concentration by evaporation at 32°C and addition of maltodextrin to 15% (wt/dry wt) prior to drying largely eliminated pigment degradation during those steps. Relative to water extracts, extracts prepared with 5 to 15% ethanol in water generally yielded more pigment with similar levels of degradation and loss during subsequent processing. Use of 5% ethanol/2% citric acid reduced yield by about half relative to water, but gave a powder with a lower degradation index and wetting time. Percentage recovery of pigment during concentration and drying was not greatly affected by solvent type or extraction temperature.     

Carbon Aerogels as Electrode Material in Supercapacitors

Due to their large specific surface area and their high electrical conductivity carbon aerogels are promising materials for electrodes in electrochemical double-layer capacitors (supercapacitor). The carbon aerogels were made via pyrolysis of resorcinol formaldehyde aerogels. The latter were prepared by supercritical and subcritical drying as well. The important findings of our investigation were, that the highest capacities of 46 F/cm³ were measured for samples with a density of about 800 kg/m³ pyrolyzed at 800°C. Also it was shown that RF-gels with molar resorcinol/catalyst ratios 1000 or higher can be dried subcritically without cracking or significant shrinkage. Carbon aerogels derived from these RF-aerogels have a small mesopore surface area, however an especially large micropore area. They provide electrical capacities which are most suitable for their use in supercapacitors.     

反式-1,4-聚异戊二烯的氯化改性

采用水相悬浮法，在常压下对反式-1，4-聚异戊二烯（TPI）进行氯化改性。研究了温度、时间、粒径等对氯化反式-1，4-聚异戊二烯（CTPI）氯含量的影响。得到适宜的反应条件是：采用两阶段升温的方法，控制一定的通氯量，第一阶段，反应温度为35℃，反应时间为2～3h；第二阶段．反应温度为50～55℃，反应时间为1～6h，可获得氯质量分数在50％以内的CTPI，产品为可溶解的白色疏松颗粒。     

Reply to the Comment by K. Jorgensen et al. to “Analysis of constant rate period of spray drying of slurry”

Previously developed model for spray drying of slurry droplets with high solid content (Liang, 2001) was revised to describe correctly a boundary condition on the outer surface of droplet on basis of the rate of liquid evaporation.     

二氧化氯分析的研究进展

二氧化氯作为新一代杀菌消毒剂，在水处理中获得越来越广泛的应用。在应用中，二氧化氯会产生分解及歧化反应，产生副产物如Cl2、ClO^-、ClO2^-、ClO3^-，所以需要对残余ClO2及这些副产物进行分析，本文对二氧化氯现有的分析方法进行了讨论。     

沉淀包覆法合成高活性纳米过渡态Al2O3粉

引言 为了提高氧化铝陶瓷的强度、韧性、致密度、透明性或降低其烧结温度等,要求采用纯度高、粒径小、粒度分布范围窄、烧结活性高的超细氧化铝粉为原料.     

我国干燥技术和装备的研究及应用

介绍我国干燥设备的开发、研究和应用情况。情况表明：我国干燥技术有很大的进步，大批进口干燥器的时代已经结束。     

An NMR study of acid sites on chlorided alumina catalysts using trimethylphosphine as a probe

The MAS-NMR spectra of adsorbed trimethylphosphine (TMP) were used to determine the concentration of Brønsted and Lewis acid sites on pure and chlorinated-Al₂O₃ samples. Chlorination with CHCl₃,CCl₄ or AlCl₃ promoted the formation of Brønsted acid centers, which are characterized by the protonated adduct of TMP. This adduct has a³¹P chemical shift of ca. –3.8 ppm and a J_P–H scalar coupling of 517 Hz. Additional resonances in the –44 to –54 ppm range are attributed to Lewis acid-base pairs. In some cases a partially resolved J_P–Al coupling is observed, which confirms the assignment. Upon thermal treatment of a chlorinated sample at temperatures > 200°C, the concentration of Brønsted acid centers decreased; the concentration of one type of Lewis acid increased and another remained almost constant. In a parallel set of experiments the initial conversion ofn-hexane at 150°C and the yields of cracking and isomerization products were determined. Comparable functional relationships were observed between the loss of Brønsted acid sites and the decrease in yields of both cracking and isomerization products. These results suggest that Bransted acidity is responsible for the cracking and isomerization ofn-hexane over chlorided aluminas at 150°C.     

FP石膏在硫化轮胎模具上的应用

主要阐述FP石膏材料、制芯工艺过程及烘干工艺，阐述了应用硅橡胶母模复制石膏芯表面光洁度高，尺寸精度较好，硫化轮胎的铸造成品率达99％以上。