余热利用系统多目标优化模型及应用

以炭黑生产中的余热利用系统为背景建立了余热利用系统多目标优化规划数学模型;阐述了模型的求解方法;给出了实例分析。     

Prediction of evaporation heat transfer coefficient and pressure drop of refrigerant mixtures

A study on the prediction of heat transfer coefficient (HTC) and pressure drop of refrigerant mixtures is reported. HTCs and pressure drops of prospective mixtures to replace R12 and R22 are predicted on the same cooling capacity basis. Results indicate that nucleate boiling is suppressed at qualities greater than 20.0% for all mixtures and evaporation becomes the main heat transfer mechanism. For the same capacity, some mixtures containing R32 and R152a show 8.0–10.0% increase in HTCs. Some mixtures with large volatility difference exhibit as much as 55.0% reduction compared with R12 and R22, caused by mass transfer resistance and property degradation due to mixing (32.0%) and reduced mass flow rates (23.0%). Other mixtures with moderate volatility difference exhibit 20.0–30.0% degradation due mainly to reduced mass flow rates. The overall impact of heat transfer degradation, however, is insignificant if major heat transfer resistance exists in the heat transfer fluid side (air system). If the resistance in the heat transfer fluid side is of the same order of magnitude as that on the refrigerant side (water system), considerable reduction in overall HTC of up to 20% is expected. A study of the effect of uncertainties in transport properties on heat transfer shows that transport properties of liquid affect heat transfer more than other properties. Uncertainty of 10.0% in transport properties causes a change of less than 6% in heat transfer prediction.     

The effect of temperature on the dynamic characteristics of heat-resistant thermoplastic composites

Two thermoplastic and two thermosetting fibrereinforced plastic composites were subjected to dynamic tests over a wide range of temperature, covering both cryogenic and hot environments. The thermal behaviour of each composite, as indicated by its dynamic mechanical properties, was assessed individually, and was compared collectively with that of the other composites.     

太阳能热水器内表面电刷镀锌

用电刷镀的方法,对尺寸为2000mm×1000mm×0.8mm 的 A_3钢板电刷镀锌保护层;并对影响镀锌层质量的因素进行了充分的研究。     

A Study of the Specific Heats of the Compounds in the Sm_2O_3-BaO-CuO System

By means of X-ray diffraction and adiabatic scanning calorimeter,the specific heatsof five compounds in the Sm_2O_3-BaO--CuO system,such as Sm_2BaO_4,Sm_2CuO_4,BaCuO_4,Sm_2BaCuO_5,SmBa_2Cu_3O_(7-x),from -150℃ to 800℃ have been measured.It is found that the specific heats ofthese compounds increase smoothly with the increase of temperature.     

管外上升R－113流体的沸腾换热试验

详细介绍了Ｒ－１１３流体管外上升流动的沸腾换热试验，包括试验台架、流量计和温度测量的修正，以及试验数据。拟合的换热关系式为ｑ＝５２８（Ｔｗ─Ｔｓ）１．３３。     

熔融还原炉内二次燃烧和传热

总结了熔融还原炉内二次燃烧和传热的研究成果，对于转炉采用二次燃烧提高废钢比也有借鉴作用。     

Relaxation phenomena caused by equilibration of point defects

Relaxation phenomena due to equilibration of point defects in metals are reviewed. The relaxation effect in specific heat observed in tungsten and platinum confirms that in both cases the nonlinear increase in the high-temperature specific heat has to be attributed to point-defect formation. Relaxation phenomena observed by measurements of electrical resistivity and positron annihilation are also considered. The comparison of the data seems to be favorable for the conclusion that all the phenomena are of one origin.     

A method to estimate entropies and heat capacities applied to alkali oxides

We present a method that is useful in the estimate and assessment of heat capacity data. The approach is based on an analysis of the logarithmic average of the phonon frequencies. In this quantity, that may be easily derived from experimental data on the vibrational entropy, the influence of atomic masses can be exactly accounted for even in polyatomic solids. Our method is applied to Li₂O, Na₂O, K₂O, Rb₂O, and Cs₂O. In particular, literature data for K₂O are critically examined.     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。