超微粒乳剂的制备及量子尺寸效应的研究

本文制备了四种不同粒度的超微粒AgBr照相乳剂,用X射线衍射技术对其粒子的大小进行了测定;观察到乳剂的紫外吸收峰随晶体颗粒的减小表现出逐渐蓝移;本文提出晶体表面的悬键的存在使得纳米晶体的平均键能升高,并对纳米AgBr乳剂的量子尺寸效应进行了解释。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

纳米复合材料——石墨层间化合物(GICs)的结构分析

本文调研了纳米复合材料——GICs(石墨层间化合物)结构的主要研究方法、原理及模型,并介绍了在GICs结构研究中用到的现代分析手段。     

镀Cu碳毡／环氧树脂复合的研制

研究了镀Ｃｕ碳毡／环氧树脂（ＣｕＣＦ／ＥＰ）复合材料的制备，并探讨了镀Ｃｕ量对碳毡电阻率，复合材料电阻率及其电磁屏蔽效率的影响规律，经合理工艺制得的镀Ｃｕ碳毡（４００ｍｇ．ｇ＾－１Ｃｕ－ＣＦ）含量为３００ｍｇ．ｇ＾－１ＣｕＣＦ／ＥＰ复合材料，其电磁屏蔽效率可在２０＝－１０００ＭＨＺ范围内达到６０ｄＢ。     

ANALYSIS ON ROOM TEMPERATURE TENSILE STRENGTH OF δ-Al_2O_3, FIBER / Al-12Si COMPOSITE

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度δｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τＰ确定复合材料的ＲＯＭ预测曲线，应首先判断σｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论。     

交联剂在碳／碳复合材料沥青基体中的作用

本文从C/C复合合材料的基体入手，分析了交联剂在沥青中的交联机理，并以此为基础对中温煤沥青在催化剂作用下进行交联反应。结果表明，交联剂在C/C复合材料基体中的交联作用非常明显，不仅基体本身的残碳率及耐热程度有很大提高，而且，以它制成的C/C复合材料的抗压强度也有显著增加。     

用于多种组装技术的厚膜导体复合结构

厚膜导体Ｐｄ－Ａｇ／Ａｕ、Ｐｔ－Ｐｄ－Ａｕ／Ａｕ平面复合结构，Ｐｄ－Ａｇ／Ａｕ立体复合结构可使多种组装技术相互兼容。立体复合结构还可有效地降低导体线电阻，减少线损耗。而且，其超声键合性尤佳     

Porous elastomeric beads from crosslinked emulsions

The production of porous polymeric particles is attractive for a large number of applications and can be achieved by various techniques. Although numerous production schemes exist for glassy polymers, difficulties arise for soft, rubbery materials that need a chemical crosslinking step, such as elastomers. This is particularly true for poly(dimethylsiloxane) (PDMS), which shows the lowest glass‐transition temperature among the polymers. Recent studies suggest in situ hydrogen bubble formation or vacuum drying of water droplets dispersed in the polymer matrix in order to generate porous PDMS structures. In this work we report early results based on the chemical crosslinking of water in PDMS emulsion droplets in a mechanically stirred thermostated water vessel. This approach is shown to lead to high porosity PDMS beads (ca. 10^?3 m particle diameter) with an open structure whose properties (diameter and porosity) are strongly influenced by the starting composition (solvent, surfactant, and polymer types and ratios), as well as the operating parameters (agitation and temperature). The possible uses of these derived beads are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 967–971, 2002     

特超稠油污水回掺降粘集输工艺

通过对河南古城油田BQ10区特超稠油乳状液的室内试验分析,指出该种乳状液的实际相突变点为68%左右,当相浓度Φ≥68%时,以W/O型为主的乳状液突变为以O/W型为主的乳状液.乳状液变型后,原油与管道内壁之间的摩擦以及原油之间的摩擦转变为水与管道内壁及水与水之间的摩擦,从而大幅度降低其粘度和摩阻损失;通过对古城BQ10区特超稠油区块单元内部污水回掺降粘集输的现场试验,证明与室内试验分析得出的结论相符合,说明区块单元污水回掺不同于常规的掺热水,也不同于掺联合站处理过的净化污水,它优于单井掺稀油.最后指出该工艺可有效地降低井站回压,方便生产管理,降低开采成本,提高采油效率和经济效益,具有低耗节能的优点.