Influence of Zn ion implantation on structures and field emission properties of multi-walled carbon nanotube arrays

The structures and field emission properties of multi-walled carbon nanotube arrays implanted with Zn+ by MEVVA ion implanter have been investigated.The results revealed that Zn+implantation induced structural damage and that the top of carbon nanotubes with multi-layered graphite structure were transformed into carbon nanowires with amorphous structure.Meanwhile,C:Zn solid solution was synthesized after Zn+ implantation.The turn-on field and threshold field were 0.80 and 1.31 V/μm,respectively for original...     

GCr15轴承钢连铸过程中热物性参数的研究

借鉴前人实验数据,采用一定的数学方法,对轴承钢的热物性参数进行了研究.结果表明：GCr15轴承钢的液相线温度为1 465.7℃,固相线温度为1 328.4℃,零强度温度为1 380℃左右,零塑性温度为1 330℃左右;在固相区、液固两相区、液相区分别采用不同的公式进行处理,可使结果更加准确,还避免了奇异性.研究结果可为轴承钢连铸工艺有限元模拟提供基础.     

Relationship of hydrocarbon and source-rock in Nos.3-5 tectonic belts of the Lenghu area, northern Qaidam Basin

Based on analyses of the components of crude oil hydrocarbons and carbon isotopes, the content of normal alkane de-creased from 49.00% to 20.10% when moving from the No.3 to No.5 tectonic belt of the Lenghu area of the Qaidam Basin, while cycloalkanes increased from 30.00% to 52.20% and aromatic and branch chain alkanes increased gradually as well. The maturity of sterane in crude oil is higher than that of its source-rock, which shows that the hydrocarbons were generated from a deep source-rock of high maturity around the tectonic belts of the Lenghu area. The analysis of the characteristics of carbon isotopes also shows that these isotopes of hydrocarbon compounds in the No.4 and No.5 tectonic belt are apparently heavier than those in the No.3 belt. The results of our research show that the hydrocarbons in the No.3 tectonic belt are mainly from a relatively rich sapropelic substance, while the hydrocarbons in the No.4 and No.5 tectonic belt originated mainly from organic matter of a rela-tively rich humic type substance.     

混合炭黑TST-103在轮胎内层帘布胶中的应用

研究了混合炭黑TST-103在轮胎内层帘布胶中的应用。小配合和车间大料及成品轮胎试验表明，使用8份混合炭黑TST-103，内层帘布胶的工艺性能、物理性能及实际使用性能均与原内层帘布胶相近，而每千克胶料成本降低了0．33元。     

Investigation of Flow Patterns in Continuous‐flow Stirred Vessels by Laser Doppler Velocimetry

The flow structure of a continuous‐flow reactor stirred by a Rushton turbine was investigated by laser Doppler velocimetry for two different mean residence time‐mixing time ratios. Velocity measurements were obtained for two inlet locations, corresponding to the incoming liquid stream being fed co‐currently or counter‐currently to the flow discharged by the turbine. In all investigated configurations and for all operating conditions, it was found that the flow disruption caused by the incoming liquid stream was observable mainly in the first vessel quarter, which followed the feed‐tube plane. From comparison of the velocities encountered in the various planes in the continuous‐flow reactor to the velocities of the batch reactor, it was also concluded that it may be possible to intensify the usage of the turbine‐stirred vessel by decreasing the characteristic times ratio, without considerable flow by‐pass and/or short‐circuiting problems.     

Calculation of single adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms on activated carbon at high pressures

A method is developed for the calculation of single-component adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms at high pressures, at two temperatures and for different mole fractions of the gas phase. The adsorption of nitrogen/methane on active carbon Norit R1 is taken as an experimental example.     

不同线密度粘胶原丝及其碳纤维的结构性能对比

用Weibull分析处理 10mm长的 4种不同线密度粘胶原丝和相应碳纤维的单丝断裂强度 ,得到原丝线密度、强度分布和碳纤维强度的对应关系。采用透射电镜 (TEM )和小角X散射 (SAXS)分析粗旦原丝 ,发现孔洞较多 ,并存在大于 70nm的大孔洞。截面和表面照片也揭示出细旦原丝截面相对规整 ,表面较光滑 ,粗旦原丝则反之。结果表明 ,原丝线密度小 ,截面形状圆整 ,缺陷少 ,所制得的碳纤维强度高。     

Intergranular oxidation of silicon in 20Cr-25Ni niobium-stabilized stainless steel at 1140–1230 K

The kinetics of intergranular oxidation of silicon in a 20Cr-25Ni Nb-stabilized stainless steel are reported, at temperatures in the range 1140–1230 K, in CO₂ at 40 bar pressure. The depth of attack increased parabolically with respect to time, with an activation energy of 335±30 kJ/mol. The mechanism of growth is discussed in terms of classical internal-oxidation theories, and an alternative explanation based on an available-space theory is developed. The internal oxidation rates in a number of different alloys are compared with diffusivities of metals in the base alloy. It is proposed that intergranular oxidation in the 20–25 Nb steel is controlled by the rate of outward diffusion of iron or chromium in the alloy.     

基于脱钩模型的新疆碳排放与经济增长的关系研究

在共建丝绸之路经济带以及生态文明的大背景下,新疆作为丝路经济带的核心区与中国西部重要的桥头堡,其经济发展的速度与效益值得关注。尤其新疆是我国重要的能源资源储备区,如何协调好能源开发过程中的碳排放与经济增长之间的关系,是当前摆在我们眼前的一大课题。本文旨在通过脱钩模型分析新疆碳排放与经济增长之间的关系,得出新疆碳排放与经济增长总体上呈现弱脱钩的结论,据此分析弱脱钩状态产生的原因,并提出了有针对性的对策建议,以期促进新疆经济能更好的适应经济新常态。     

Effects of coagulation bath temperature on structure and performance of poly （vinyl butyral） hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.