浅谈如何生产质量稳定的乳化炸药

通过大量的试验及理论分析 ,总结出影响乳化炸药质量稳定的原因 ,并制定了提高质量稳定的措施     

OPS和OPC系列稠油乳化降黏剂的研制

以工业品烷基酚聚氧乙烯醚OP-n（n=4,6,8,10,15）为起始原料,合成了烷基酚聚氧乙烯醚乙酸盐OPC-n和磺酸盐OPS-n两个系列的阴-非离子表面活性剂。以酸值和黏度不同的胜利单家寺和陈庄稠油为实验油样。将OPC-n和OPS-n溶于矿化度5811 mg/kg的胜利标准盐水和NaCl、CaCl2盐水中作为水相,按油、水质量比7∶3在50℃用玻棒搅拌混合,观察是否形成水包油乳状液并测黏度进行确认。在胜利标准盐水溶液中,OPC-n和OPS-n乳化稠油所需的最低质量分数,随稠油、表面活性剂类型及氧乙烯链节数n而变,一般而言,OPC-n系列中的OPC-8和OPS-n系列中的OPS-4乳化稠油的性能最好,该最低质量分数值分别为0.05%或0.025%和0.025%。在NaCl盐水溶液中,OPC-n的该最低质量分数值与稠油和n有关,均随盐含量增加而增大,在盐含量≤15%时,抗盐性最好的OPC-8和OPC-10的该值≤0.05%;OPS-n的抗盐性好于OPC-n。OPC-n的抗钙性良好,钙盐含量为2%时该最低质量分数≤0.1%;OPS-n的抗钙性更好,钙盐含量为2%和3%时该最低质量分数仅为0.025%或0.05%。表6参5。     

γ 射线引发 VAc 乳液聚合以制备白乳胶的动力学及工艺条件研究

研究了ＶＡｃ的辐射乳液聚合动力学，并对其聚合工艺条件作了初步探索。得出ＶＡｃ乳液在进行辐射聚合时，成核期结束较早（转化率在１０％以下），有相当长的恒速期存在。乳胶粒子直径在０．５～３μｍ之间，比一般的乳液聚合乳胶粒子要大。同时从动力学数据还可以看出几种成核机理（胶束成核，水相成核和液滴成核）同时存在，由此对试验条件提出了相应的要求。     

乳状液膜法制备草酸稀土

系统研究了在乳状液膜内水相直接制备草酸稀土的方法，讨论了内水相草酸浓度、表面活性剂浓度、载体浓度、外水相酸度和外水相稀土浓度对迁移率的影响，找到了制备草酸稀土的最佳条件，草酸稀土经灼烧所得的氧化物含ＲＥ２Ｏ３〉９９．５％，与萃取法相比，此方法具有成本低、能耗少、污染程度低的特点，具有工业化前景。     

乳化液泵站变频调速系统的设计

针对传统的乳化液泵站调速系统存在机械损耗比较大的问题,提出了一种乳化液泵站变频调速系统的设计方案;给出了该系统的硬件结构,详细介绍了该系统的工作模式及软件设计。实际应用表明,该系统运行稳定、机械损耗小。     

Synthesis and microwave characterization of Co-SiC core-shell powders by electroless plating

Co-SiC core-shell powders were prepared by electroless plating. Scanning electron microscopy （SEM） revealed that Co-SiC core-shell powders were of nearly sphere-like shape and were about 0.3 pan. X-ray powder diffraction （XRD） patterns showed that the cobalt powder was hexagonal crystallite. The complex dielectric constant and the complex permeability of Co-SiC core-shell powders-paraffin wax composite were measured by the rectangle wavegnide method. It showed that the dielectric loss was less than 0.1 and the magnetic loss was about 0.2 in 8.2-12.4 GHz for prepared Co-SiC core-shell comoosite oowders.     

Coaxial Alginate Hydrogels: From Self-Assembled 3D Cellular Constructs to Long-Term Storage

Alginate as a versatile naturally occurring biomaterial has found widespread use in the biomedical field due to its unique features such as biocompatibility and biodegradability. The ability of its semipermeable hydrogels to provide a favourable microenvironment for clinically relevant cells made alginate encapsulation a leading technology for immunoisolation, 3D culture, cryopreservation as well as cell and drug delivery. The aim of this work is the evaluation of structural properties and swelling behaviour of the core-shell capsules for the encapsulation of multipotent stromal cells (MSCs), their 3D culture and cryopreservation using slow freezing. The cells were encapsulated in core-shell capsules using coaxial electrospraying, cultured for 35 days and cryopreserved. Cell viability, metabolic activity and cell–cell interactions were analysed. Cryopreservation of MSCs-laden core-shell capsules was performed according to parameters pre-selected on cell-free capsules. The results suggest that core-shell capsules produced from the low viscosity high-G alginate are superior to high-M ones in terms of stability during in vitro culture, as well as to solid beads in terms of promoting formation of viable self-assembled cellular structures and maintenance of MSCs functionality on a long-term basis. The application of 0.3 M sucrose demonstrated a beneficial effect on the integrity of capsules and viability of formed 3D cell assemblies, as compared to 10% dimethyl sulfoxide (DMSO) alone. The proposed workflow from the preparation of core-shell capsules with self-assembled cellular structures to the cryopreservation appears to be a promising strategy for their off-the-shelf availability.     

高含水油包水乳化液稳定性机理及实验研究

本文在对油包水乳化液的微观机构进行分析的基础上，对高含水油包水乳化液的稳定性机理进行了实验研究，初步分析了它的流变性质。本文的研究对于油包水乳化液降低成本，提高性能的发展具有重要的理论意义。     

Stereocomplex Crystallization Induced Significant Improvement in Transparency and Stiffness–Toughness Performance of Core-Shell Rubber Nanoparticles Toughened Poly(l-lactide) Blends

Toughening modification of poly(l -lactide) (PLLA) with rubber particles is often realized at the cost of transparency, mechanical strength, and modulus because high rubber loadings are generally required for toughening. In this work, a promising strategy to simultaneously improve the transparency and stiffness–toughness performance of poly(butyl acrylate)-poly(methyl methacrylate) (BAMMA) core-shell rubber nanoparticles toughened PLLA blends by utilizing the stereocomplex (SC) crystallization between PLLA and poly(d -lactide) (PDLA) is devised. The results reveal that the construction of SC crystallites in PLLA matrix via melt-mixing PLLA/BAMMA blends with PDLA can prevent BAMMA nanoparticles from aggregation and promote them to form network-like structure at lower contents. As a result, not only higher toughening efficiency with less rubber contents but also superior transparency is achieved in the PLLA/PDLA/BAMMA blends as compared with the PLLA/BAMMA ones where large aggregated BAMMA clusters are formed. Moreover, the outstanding reinforcement of SC crystallites network for PLLA can impart an enhanced tensile strength and modulus to PLLA/PDLA/BAMMA blends, thus improving the stiffness–toughness performance of PLLA/PDLA/BAMMA blends to a higher degree. This work demonstrates that SC crystallization is a promising solution to solve the contradiction between transparency and mechanical properties and then obtain superior comprehensive performances in rubber toughened PLLA blends.     

Micron-Scale Soft Actuators Fabricated from Multi-Shell Polystyrene Particle-Gold Nanoparticle Nanohybrids

Actuators made of soft matter are needed for a variety of fields ranging from biomedical devices to soft robotics to microelectromechanical systems. While there are a variety of excellent methods of soft actuation known, the field is still an area of intense research activity as new niches and needs emerge with new technology development. Here, a soft actuation system is described, based on a core-multi-shell particle, which moves via photothermal expansion. The system consists of a novel polystyrene-based thermally expandable microsphere, with a secondary shell of a silicate-silane graft copolymer, to which gold nanoparticles are covalently linked. The gold nanoparticles act as photothermal nano-transducers, converting light energy into the thermal energy necessary for microsphere expansion, which in turn results in material movement. Actuation is shown in isolated particles in thermal and photothermal regimes using metal ceramic heaters or 520 nm laser illumination, respectively. Macroscale actuation is demonstrated by making a composite material of particles suspended in the transparent elastomer polydimethylsiloxane. The sample demonstrates an inchworm-like movement by starting from an arched geometry. Overall, this work describes a new particle-based actuation method for soft materials, and demonstrates its utility in driving the movement of a composite elastomer.