空冷器复合管束力学建模和数值模拟

对加氢空冷器复合管束进行结构分离和解析,根据弹塑性力学方法获得复合管的力学分析控制方程,对内衬316L不锈钢的复合管进行应力场数值模拟,比较弹性力学和有限元数值模拟方法得到的应力分析结果相互吻合;分析复合管的极限工作载荷以及运行工况下的热应力,提出以结合强度为空冷器复合管束检验的指标,并对实际制造的复合管样品进行结合强度测试,结果满足相关国家标准,工程应用实现了设备长周期运行.     

电弧喷涂锡基巴氏合金层的磨损性能

针对电弧喷涂巴氏合金涂层组织的特殊性,研究在润滑条件下巴氏合金涂层的摩擦磨损性能,对该涂层的工程应用具有重要的参考价值.利用环块摩擦磨损试验分别对比了电弧喷涂、铸造以及堆焊方法制备的巴氏合金层与碳钢和铸铁构成摩擦副的磨损表现.借助于扫描电子显微镜、x 射线能谱以及x 射线衍射,分析了巴氏合金涂层的微观组织结构和磨损表面形貌,研究了其组织变化与耐磨性能之间的关系.实验结果表明：在润滑条件下,电弧喷涂巴氏合金涂层具有比铸造巴氏合金更好的减磨性能;选择合适的工艺参数可以制备组织致密、结合强度高,且具有很好磨损性能的巴氏合金涂层.     

Effect of Curing Regime on Bonding Strength of EVA Modified Mortar to Tile

Ethylene-Vinyl Acetate (EVA) redispersible powder and latex were used to modify mortar. Three kinds of curing regimes: standard curing, high temperature curing and freeze-thaw circle curing were adopted to cure the bonded samples. Bonding strength of EVA modified mortar was tested at 28 days. The development of bonding strengths under all three curing regimes were discussed and compared. The experimental results show that bonding strength increases with the increase of EVA content in mortar. The curing regi...     

Oxidation and Fracture Strength of High-Purity Reaction-Bonded Silicon Nitride

Reaction-bonded Si₃N₄ (RBSN) made from high-purity Si powder is unusually resistant to degradation caused by exposures to air for up to 50 h at temperatures up to 1400°C. The weight gain during oxidation of this SiH₄-originating RBSN is approximately 10 times less than conventional RBSN. Contrary to normally observed strength degradations, room-temperature strengths of this high-purity, oxidized RBSN (avg = 435 MPa, max. = 668 MPa) remained at their unusually high, as-processed levels after 1000° and 1400°C oxidizing exposures. Fracture toughness values were unaffected by oxidation ( K _IC= 2.3 to 2.4 MPa · m^1/2). This superior oxidation resistance results from the high purity and the small diameter pore channels (0.01 to 0.06 μm) achieved in this SiH₄-originating RBSN.     

用高分子材料修复舰艇大轴

舰艇大轴在海水中严重腐蚀后,采用粘接技术,选用国产高强度金属修补剂,对大轴局部腐蚀部位进行修理,对提高大轴使用寿命,防止大轴再腐蚀起到有效作用.     

h-BN掺杂对金刚石晶体结构的影响

报道了在Fe70Ni30合金触媒和石墨系体中,掺杂六角立方氮化硼(h-BN)和硼(B)生长金刚石单晶的过程。研究发现,h-BN和B掺杂对于金刚石生长条件及形貌等具有较大的影响,其中h-BN掺杂生长金刚石的最低生长压力达到了6.2 GPa,同时晶体呈绿色条状。说明h-BN和B在金刚石晶体生长以及取代碳原子进入晶格时起到了不同的作用。通过X射线衍射及光电子能谱等表征手段,分析了硼氮对金刚石晶体结构的影响,以及硼氮在金刚石中的化学环境及成键方式。在此基础上阐述了硼氮掺杂的形成机制。     

Microstructural characterization of Cu/Al composites and effect of cooling rate at the Cu/Al interfacial region

Cu/Al composites are of vital importance in industrial applications because of their numerous advantages. The influence of bond-ing temperature and cooling rate on the microstructure and morphology of ...     

Ti、Mo、W、Cr及其合金镀层与超硬磨料之间结合性能的研究

本文在研究金属与超硬磨料之间作用的基础上，讨论了实现镀层与磨料形成强力结合的条件，为高性能超硬工具的制造提供了理论和实践依据。     

钛合金与不锈钢的相变超塑性扩散焊工艺

用相变超塑性扩散焊法实现了钛合金TA17与不锈钢0Cr18Ni9Ti之间的连接.研究了工艺参数对接头强度的影响,得到试验条件下钛合金与不锈钢焊接的优化工艺参数为循环上限温度890℃, 循环下限温度800℃, 循环次数10, 焊接压力5MPa, 循环加热速度30℃/s.在优化的工艺条件下,接头强度达到307MPa,而焊接时间仅为160s.对拉伸断口进行了扫描电镜观察、能谱分析和X射线衍射分析,发现断裂沿FeTi和β-Ti层之间的某一个位置发生,FeTi金属间化合物层是接头的最薄弱环节.对接头进行了能谱分析,结合Fe-Cr-Ti三元相图发现,钛合金与不锈钢之间的反应区内依次形成了σ、Fe2Ti、FeTi和β-Ti层.     

New developments in cold spray based on higher gas and particle temperatures

In cold spraying, bonding is associated with shear instabilities caused by high strain rate deformation during the impact. It is well known that bonding occurs when the impact velocity of an impacting particle exceeds a critical value. This critical velocity depends not only on the type of spray material, but also on the powder quality, the particle size, and the particle impact temperature. Up to now, optimization of cold spraying mainly focused on increasing the particle velocity. The new approach presented in this contribution demonstrates capabilities to reduce critical velocities by well-tuned powder sizes and particle impact temperatures. A newly designed temperature control unit was implemented to a conventional cold spray system and various spray experiments with different powder size cuts were performed to verify results from calculations. Microstructures and mechanical strength of coatings demonstrate that the coating quality can be significantly improved by using well-tuned powder sizes and higher process gas temperatures. The presented optimization strategy, using copper as an example, can be transferred to a variety of spray materials and thus, should boost the development of the cold spray technology with respect to the coating quality. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, OH, 2006.