基于SHARC数字脉压系统的设计与实现

详细介绍了采用两片浮点DSP ADSP21062实现某舰载雷达所需要完成的舰速补偿、反异步干扰和脉冲压缩的系统研制。通过采用分段匹配滤波的方法，极大地节约了时间和空间。与完成同样功能采用单片TMS320C6701的设计相比，本设计具有外围电路简单、系统调试容易等优点。     

梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.     

考虑弯道环流影响的平面二维水流泥沙数学模型

弯道环流是影响断面流速和含沙量分布的重要因素。本文提出了通过求解立面二维弯道环流运动的方法,在平面二维水流泥沙数学模型中考虑弯道环流的作用。该方法适用范围广,增加计算工作量不太大。     

A simple correlation for gas bubbles rising in power‐law fluids

Recently, the author (Rodrigue, 2001 a, b) proposed a generalized correlation for the steady rise of gas bubbles in uncontaminated viscous Newtonian fluids of infinite extent. It is the purpose of this note to show that this model can be modified for inelastic non‐Newtonian power‐law fluids. Using data taken from six different studies, it is shown that the modified model can predict quite nicely the bubble velocity for these non‐Newtonian inelastic fluids.     

Prediction of axial velocity profiles and solids hold-up in a rotary kiln

Axial bed depth profiles were experimentally measured in a rotary kiln containing ilmenite particles under steady state and transient conditions. The variables include feed rate of solids, inclination and rotational speed of the kiln. and dam height. The variation of the axial velocity with kiln axis was estimated. The semi-experimental model proposed by Perron and Bui (1990) was modified to include the effect of the variables of the present study. The mean residence time of solids was estimated from the fractional hold-up and expressed in terms of the process variables. The transients induced by a step change in any of the operating conditions were measured as variation of discharge rate of solids with time.     

外焊缝自动跟踪系统

介绍了外焊缝自动跟踪系统的组成及工作原理，简述了传动部分ＧＴＲ－ＰＷＭ调速系统，给出了系统的硬件电路。该跟踪器具有结构简单，体积小，性能稳定等特点，在生产线上获得了成功的应用。     

High-temperature,high-pressure thermophysical measurements on liquid zinc

Wire-shaped zinc samples were resistively volume heated as part of a fast-capacitor discharge circuit. Time-resolved measurements with submicrosecond resolution of the current through the specimen, the voltage drop across it, and the thermal expansion of the specimen as a function of time allow determination of the enthalpy, electrical resistivity, and density at different temperatures up to superheated liquid states of zinc far above the normal boiling point. High static pressures, up to 3800 bar of the ambient medium water, were used. An estimate of the critical pressure for zinc is given by investigations of the stability of the sample with a framing CCD camera, taking pictures of different samples varying the ambient static pressure. The critical volume and the critical temperature are obtained by means of an extrapolation of measured data at different pressures.Paper presented at the Fourth International Workshop on Subsecond Thermophysics, June 27–29, 1995, Köln, Germany.     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

Transport properties of 1,1-difluoroethane (R152a)

Based on reliable. carefully selected data sets. equations for the thermal conductivity and the viscosity of the refrigerant R 112a are presented. They are valid at temperatures from 240 to 440 K, pressures up to 20 MPa. and densities up to 1050 kg · m^–3. including the critical region.