Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

Study of the effective parameters on mechanical and electrical properties of carbon black filled PP/PA6 microfibrillar composites

In this study the electrical and mechanical properties of microfibrillar polypropylene (PP)/polyamide6 (PA6) blend filled with super conductive carbon black (CB) have been investigated. In situ microfibrillar PP/PA6 composites filled with CB are produced using a single screw extruder equipped with a spinneret. Glycidyl methacrylate (GMA) grafted polypropylene (PP-g-GMA) is used as the compatibilizer. To investigate the effects of extensional flow on the microstructure, electrical and mechanical properties, three adaptors with various convergence angles were designed, prepared and applied between the extruder and the spinneret. To optimize the effects of processing and material parameters on the electrical and mechanical properties, the Taguchi method of experimental design is used. Material and processing factors which are studied include: concentration of PA6, compatibilizer level, CB concentration, drawing speed of melt spinning line, adaptor angle, order of mixing and temperature profile along the extruder. The results show an increase in DC conductivity of up to 10¹¹ times in comparison with pure PA6, by increasing the concentration of CB, drawing speed, adaptor angle and optimizing other parameters. By optimizing processing and material factors studied here, strength of microfibrillar structured composites is increased of up to 80% in comparison to pure PP.     

Analytical modeling and experimental study of tensile strength of asphalt concrete composite at low temperatures

In this study, analytical modeling of the tensile strength of hot-mix asphalt (HMA) mixtures at low temperatures was developed. To do this, HMA mixtures were treated as a two-phase composite material with aggregates (coarse and fine) dispersed in an asphalt mastic matrix. A two-phase composite model, which was similar to Papanicolaou and Bakos's [J. Reinforced Plast. Compos. 11 (1992) 104] model with a particle embedded in an infinite matrix, was proposed. Unlike Papanicolaou and Bakos's model, an axial stress was introduced to the fiber end to consider the load transferred from the asphalt mastic the aggregate. Efforts were also made to consider the effect of aggregate gradation, asphalt mastic degradation, and interfacial damage between the aggregates and asphalt mastic matrix on the tensile strength of the HMA mixtures. Experimental investigations were conducted to validate the developed theoretical relations. A reasonable agreement was found between the predicted tensile strength and the experimental results at low temperatures. Parameters affecting the tensile strength of asphalt mixtures were discussed based on the calculated results.     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

Design of the ECRH/ECCD Launcher System for HL-2A Tokamak

An ECRH/ECCD system with two 68GHz/500kW/1S gyrotrons will be built up in HL-2A tokamak. The location of the Gaussian beam waist is 580 mm away from the center of the plasmas and the beam radius is 37 mm at the center of the plasmas. Compared to the minor plasma radius （420 mm）, it is small enough for localized control. The launcher system covers a wide toroidal and poloidal steering range by the two steering plane mirrors. Therefore it is possible to explore the on- and off-axis heating over half of the plasma minor cross section and the co-current drive.     

Electrochemical noise analysis for estimation of corrosion rate of carbon steel in bicarbonate solution

We have investigated the electrochemical noise behavior of carbon steel in fully deaerated aqueous bicarbonate solutions, and discussed the optimum conditions of the noise analysis for estimating corrosion rate of the steel. Noise of the potential difference and of the short-circuit current between two identical steel coupons were successfully measured. The time-series noise patterns were transformed into frequency domain by fast Fourier transformation, and then their power spectrum densities (PSDs) at a frequency were determined to be compared with the corrosion rate. The PSDs of the potential and of the current varied with changing environmental factors of bicarbonate concentration, pH, and immersion time. The factors also controlled the corrosion rate of the steel. The PSDs were associated with the corrosion rate, and then it was found that the PSDs of the potential and of the current showed linear correlation with the corrosion rate in log-log scale. There was also linear relationship between the corrosion rate and a spectral noise resistance obtained from the PSDs of the potential and the current. The linearities of the three correlations were better at a lower analyzed frequency. Furthermore, the PSDs of the current and the noise resistance indicated more linear correlation with the corrosion rate than that of the potential. As the simplicity of the measurement system is additionally considered, it is concluded that the PSD of the current noise at an analyzed frequency of 3 mHz is the optimum conditions for estimating the corrosion rate from 10⁻² to 10⁰ A m⁻² in this study.     

I2C总线及其在单片机测控系统中的应用

介绍了I2C总线的基本工作原理和I2C总线串行EEPROM,以及AT24C08A在某单片机控制系统中的应用.经过系统的使用,证明I2C总线的EEPROM能可靠地工作.     

人工神经网络A／D变换器

本文对［５］的４位人工神经网络Ａ／Ｄ变换器进行了研究．指出按其方法推广实现多位Ａ／Ｄ时存在突触电阻大小以至无法实现且抗干扰能力也不好的问题并给出了解决办法．同时对如何改善神经元转移特性的硬限幅曲线作了简单讨论．     

多路缓变信号记录仪

本文介绍了多路缓变信号记录仪的系统构成,研究设计了多路缓变信号记录仪的硬件电路,较详细地介绍了该系统的工作原理及软件编程要点。     

活性碳和5A分子筛的吸附特性及其在真空获得中的作用

评述了活性碳和５Ａ分子筛的吸附等温线及其在真空佩温绝热夹层真空获得中的作用。分析了真空夹层抽真空除气时用Ｎ＿２气置换以及用“多次吸附－脱附Ｎ＿２气”方法活化吸附剂等先进工艺的机理。论述了根据吸附剂吸水的吸附等温线，合理确定活化工艺条件的方法。