Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

环氧树脂及其增强材料回顾

本文回顾了PCB制造常用的环氧树脂及其增强材料的性能和用途。同时,还介绍了代用树脂材料和代用增强材料的最新进展,如改性环氧树脂、无卤树脂、Thermount、PTFE、氰酸酯等,并就其性能进行了探讨。     

微机械可调谐滤波器的研制

利用 Ga As/Al Ga As分布反馈 Bragg反射镜在 Ga As衬底上制作了一个微机械的调谐滤波器 .该器件在 7V调谐电压下调谐范围达28nm     

In-tube condensation of mixture of R134a and ester oil: empirical correlations

This paper presents a comparative study of the condensation heat transfer coefficients in a smooth tube when operating with pure refrigerant R134a and its mixture with lubricant Castrol “icematic sw”. The lubricant is synthetic polyol ester based oil commonly used in lubricating the compressors. Two concentrations of R134a-oil mixtures of 2% and 5% oil (by mass) were analysed for a range of saturation temperatures of refrigerant R134a between 35 °C and 45 °C. The mass flow rate of the refrigerant and the mixtures was carefully maintained at 1 g/s, with a vapour quality varying between 1.0 and 0. The effects of vapour quality, flow rate, saturation temperature and temperature difference between saturation and tube wall on the heat transfer coefficient are investigated by analysing the experimental data. The experimental results were then compared with predictions from earlier models [Int J Heat Mass Transfer (1979), 185; 6th Int Heat Transfer Congress 3 (1974) 309; Int J Refrig 18 (1995) 524; Trans ASME 120 (1998) 193]. Finally two new empirical models were developed to predict the two-phase condensation heat transfer coefficient for pure refrigerant R134a and a mixture of refrigerant R134a with Castrol “icematic sw”.     

任意取向多个介质旋转椭球的散射场

本文提出了一种用于计算任意取向多个介质椭球电磁散射的混合方法.利用扩展边界条件(EBC)导出具有旋转轴对称单个椭球以球面波矢量函数为基底的T矩阵,结合球矢量波函数旋转定理和递推T矩阵方法,给出多个任意取向介质椭球的散射场.数值例子验证了该混合方法的计算精度和有效性.     

Ca掺杂钨镁酸铅陶瓷材料的制备及其介电性能

研究了Ca掺杂钨镁酸铅(PMW)陶瓷材料的合成、结构、烧结以及介电性能。结果发现：在Ca^2 摩尔分数小于15％时，能形成单相的PCMW钙铁矿相，结构由原来的斜方相向立方相转变。用二步合成法制备的样品容易致密烧结，气孔率比一步法制备的样品小。Ca的加入降低了材料的介电损耗，在频率为1MHz时，介质损耗达到了10^-4。当Ca^2 摩尔分数大于10％时，材料的Curie峰宽化显著，介电常数温度系数降低。     

经济实用的DSP电源解决方案

笔者介绍了两种低纹波的DSP电源解决方案:一为采用MAX1793和大电流EMI静噪滤波器NFM41P;二为改进的去耦p型滤波电路和大电流EMI静噪滤波器NFM41P。并对方案的特点及其实现进行了详细的解析。试验结果表明:所述方案的纹波小,仅100 mV左右;成本低,仅几十元;适用范围广,通过改变MAX1793芯片的输出电压,可将本方案移植到TI的C5000,C6000系列,且还可用于其他的脱机工作系统。     

改性双马来酰亚胺的研究

本文研究了双马来酰亚胺与烯丙基化合物形成的改性树脂体系的固化和热性能，讨论了单体配比、增韧剂、催化剂对性能的影响。     

采用纯化学物质校准仪器测定钛合金中碳量

采用纯化学物质对高频加热－红外检测碳硫仪校准，对钛合金中的碳量进行测定。     

带隔板底水油藏油井临界产量计算公式

本给出了带隔板底水油藏油井的监界产量计算公式，它适用于所有带隔板底水油藏的油井。