TE011模高功率窄带带通滤波器设计

利用圆腔ＴＥ０１１模的高Ｑ值特性，设计了高直接耦合式窄带带通滤波器，并给出了具体的设计步骤和实例，理论与实验结果基本一致。     

Dielectric properties of SBR vulcanizates loaded with HAF carbon black and BaTiO3 ceramics

The influence of HAF carbon black and BaTiO₃ ceramic powder contents in SBR vulcanizates on the dielectric constant (ε′) at different frequencies and at fixed temperature of 303 K is studied well in this article. The temperature dependence of the ac conductivity (σ_ac) was also studied. ε′ appreciably decreases as frequency increased for both filled and unfilled SBR vulcanizates. At each frequency, ε′ gradually decreased with BaTiO₃ loading, but its change at any fixed frequency with BaTiO₃ filler loading is not uniform. For HAF group ε′ (at loading ≥ 40 phr), drops rapidly with frequency. Meanwhile, it increased appreciably beyond a certain HAF filler loading (≈ 20 phr). Experimental values of the dielectric constant of both BaTiO₃ and HAF contents were compared with those calculated by using Tsangaris, Clausius and Bruggman models. Tsangaris model with simple modifications was applied and a fairly good agreement was obtained. The HAF particles or aggregates was found to take the shape of oblate ellipsoids with the minor axes parallel to the applied frequency as detected from the decreasing behavior of the depolarizing factor (Y) with HAF contents. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2227–2234, 2007     

初级馈源位置对Fabry-Perot谐振天线性能的影响

通过平面波叠加法,分析了初级馈源位置对PEC和PMC作为接地板的2类Fabry-Perot谐振天线的最大方向性系数及其带宽的影响。分析表明初级馈源位置在满足特定条件取值时,Fabry-Perot谐振天线将获得最大的定向性,但其定向性带宽并不随馈源位置有明显改变。同时,首先指出定向性与其带宽的乘积仅是Fabry-Perot谐振天线的反射盖板其反射系数模的函数,并随着反射系数模的增加而趋于某一定值。最后进行了仿真验证,仿真结果与理论计算具有很好的一致性,对Fabry-Perot谐振天线的设计具有很好的理论指导意义。     

球平面开放腔设计与Q值测量

本文介绍了设计及测试球平面准光学开放腔(准光腔)的过程,对腔内稳定振荡场分布、菲涅尔数进行了细致分析,阐述了球平面准光腔的设计制作要点,介绍了用于介质测试的准光腔扫频测量系统,并采用标量网络分析仪(SNA)对准光腔进行了品质因数测定.     

a-C:F:H films prepared by PECVD

Fluorinated amorphous hydrogenated a-C:F:H carbon thin films were deposited using radio frequency plasma enhanced chemical vapor deposition(RF-PECVD) reactor with CF4 and CH4 as source gases and were annealed in a N2 atmosphere. The properties of these films were evaluated by FTIR spectrometry, UV-VIS spectrophotometry and single-wavelength spectroscopic ellipsometry. A correspondence relativity connection between the deposition rate and technology was found. The chemical bonding structures and the content of CHx and CFx in the films are transformed and the optical band gap decreases monotonically with increasing temperature after annealing.The dielectric constant is increased with decreasing content of F in the films and the optical band gap is decreased with decreasing the content of H in the film.     

浅谈BaO-Ln2O3-TiO2体系微波介质陶瓷的热稳定性

本文介绍了目前提高BaO-Ln2O3-TiO2体系微波介质陶瓷热稳定性的几种方法,指出了有待解决的主要问题;而加强对陶瓷结构的理论剖析、寻找合适的添加剂、改进制备工艺等是今后研究工作的重点。     

钛酸锶钡陶瓷材料的掺杂改性

钛酸锶钡(BST)是一种重要的具有钙钛矿结构的铁电材料。顺电态下,其介电损耗较小,结构稳定。因此对顺电态下的BST进行掺杂改性是近年来铁电材料的研究热点之一。本文简要介绍了目前国内外科研工作者利用稀土、碱土氧化物进行掺杂时对BST的微观结构、介电损耗、介电常数以及可调率方面的影响。     

掺钇铌酸锌铋陶瓷的介电性能

通过X射线衍射、扫描电镜、精密阻抗分析仪等对A位Y3 取代的Bi(1.5-x)YxZnNb1.5O7介质陶瓷样品的结构和介电性能进行了研究.结果表明:当Y3 取代量较少时(x≤0.2),样品保持立方焦绿石结构;当Y3 取代较多时(x≥0.4),样品出现第二相.随着取代量的增加,样品的致密化温度升高,表观密度减小,晶粒尺寸减小,介电常数减小,介电损耗增加.Y3 取代后(x≤0.8),样品的温度系数得到优化,且具有良好的高频稳定性.低温的介电弛豫现象随着Y3 取代的增加发生有规律的变化,表现为介电常数下降,介电常数峰宽化和平坦.     

Ba（Sn0．1Ti0．9）O3粉体的熔盐法制备与性质

采用熔盐法研究了Ba（Sn0．1Ti0．9）O3铁电体粉体的制备工艺和粉体性质。探讨了在熔盐催化下，合成温度对Ba（Sn0．1Ti0．9）O3反应完全程度及粉体形态的影响。结果表明，当反应温度达到900℃时，在熔盐环境下即可合成单相固体Ba（Sn0．1Ti0．9）O3，随着反应温度提高，粉体尺寸变化不大，但当温度超过950℃时出现晶粒异常长大趋势。烧结陶瓷的形貌和介电性质显示陶瓷粉体烧结活性好且介电性质优良。     

溶胶-凝胶法制备的钛酸锶钡超细粉体的结构与性能

采用溶胶-凝胶法制备了不同Ba／Sr比的BST粉体，研究了粉体的热处理制度，粉体及其烧结体的微观结构，烧结体的介电性能以及居里温度与组成的关系等。研究结果表明用溶胶．凝胶法制备的BST超细粉体，由于其尺寸细小，粉体的比表面积很大，因而烧结活性更高，在1350℃烧成4h可获得结构致密的单一钙钛矿相的瓷体。