Kernel-based fourth-order diffusion for image noise removal

The fourth-order partial differential equations have good performance on noise smoothing and edge preservation without creating blocky effects on smooth regions. However, for low signal-to-noise ratio images, the discrimination between edges and noise is a challenging problem. A novel kernel-based fourth-order diffusion is proposed in this paper. It introduces a kernelized gradient operator in the fourth-order diffusion process, which leads to more effective noise removal capability. Experiment results show that this method outperforms several previous anisotropic diffusion methods for noise removal and edge preservation.     

A model for multicomponent diffusion in oxide melts

A general flux equation for multicomponent diffusion in oxide melts is presented. An explicit method was developed to calculate the gradients of single-ion activities from those of oxides with the constraints of local equilibrium and electroneutrality. This resolves ambiguity in quantifying the thermochemical driving force for ionic diffusion. A model equation for multicomponent ionic diffusion was derived within the framework of non-equilibrium thermodynamics by de Groot and Mazur. The proposed model takes empirically measurable quantities as input variables, so the diffusion calculations are consistent with thermochemical data, as furnished by the CALPHAD (CALculation of PHAse Diagrams) method, as well as ionic mobility measurements. Although the model is derived for oxides, it can be applied to diffusion in other concentrated liquid electrolytes, such as chloride and fluoride melts. Formulas for multicomponent ionic diffusion in various reference frames are presented with respect to mole fraction.     

Tailoring the electron-blocking layer by addition of YSZ to Ba-containing anode for improvement of ceria-based solid oxide fuel cell

The in-situ fabrication of an electron-blocking layer between the Ba-containing anode and the ceria-based electrolyte is an effective approach in suppressing the internal electronic leakage in ceria-based solid oxide fuel cell (SOFC). To improve the thickness of the electron-blocking layer and to research the effect of the layer thickness on the improvement of SOFC, a Ba-containing compound (0.6NiO-0.4BaZr_0.1Ce_0.7Y_0.2O_3-δ) modified by Y stabilized zirconia (YSZ) was employed as a composite anode in this research. SEM analyses demonstrated that the thickness of the interlayer can be simply controlled by regulating the proportion of YSZ at anode. The in-situ formed interlayer in the cell with the anode modified by 20?mol% YSZ possesses a thickness of 0.9?µm which is more suitable for the cell achieving an enhanced performance.     

How to accelerate green technology diffusion? Directed technological change in the presence of coevolving absorptive capacity

The time window for effective climate change mitigation is closing. Technological change needs to be accelerated to limit global warming to a manageable level. Path dependence of technological change is one explanation for sluggish diffusion of green technologies. Firms acquire capital that differs by technology type and build up type-specific technological know-how needed to use capital efficiently. Path dependence emerges from cumulative knowledge stocks manifested in the productivity of supplied capital and firms’ capabilities. Increasing returns arise from induced innovation feedbacks and learning by doing. Relatively lower endowments with technological knowledge are a barrier to diffusion for new technologies. This paper shows how the evolution of relative stocks of technological knowledge explains different shapes of diffusion curves. Using an eco-technology extension of the macroeconomic agent-based model Eurace@unibi, it is shown how the effectiveness of different climate policies depends on the type and strength of diffusion barriers. Environmental taxes can outweigh lower productivity and subsidies perform better if lacking capabilities hinder firms to adopt a sufficiently mature technology.     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

弯曲性分叉河道中污染物扩散性的初步研究

弯曲性分叉河道中水流特征复杂,对污染物扩散有很大影响。为了定量分析其水流特征对污染物扩散的影响,采用有限元方法求解弯曲性分叉河道中的污染物扩散数学模型,研究其中污染物扩散的状况。主要针对河道回流、绕流对污染物扩散的影响进行了详细数值模拟计算,并分别给出了可视化结果及平均的扩散距离。计算结果表明:边界层稍微减弱污染物的扩散,弯道分离使污染物扩散呈现多向扩散,而回流和绕流尾迹区使污染物很难扩散,从而有利于泄漏污染物的收集和集中治理。     

基于单片机加压控制的PCD复合片真空扩散焊接

文章针对普通钎焊的聚晶金刚石钻头剪切强度不高，提出了采用单片机加压控制的PCD复合片真空扩散焊接的设计思想，在对原真空扩散焊机液压改造的基础上给出如何由单片机控制加压的电路和程序流程设计。实际应用表明，该技术经济实用，有较好的经济效益。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.