Si衬底上Ta-N/Cu薄膜性能研究

对Si衬底上Ta-N/Cu薄膜进行了电学和热学分析，结果发现500℃以下薄膜电随几乎不变，600-690℃下的退火引起的电阻率降低是由于Ta-N电阻的热氧化和Cu熔化扩散引起的，而690℃以上的电阻率增加是由于Cu引线传输能力减弱所致，为0.18μm以下的超大规模集成电路中的Cu引线和电阻薄膜的制作提供了有益的借鉴。     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

高温和低张应力引起的非平衡晶界偏聚动力学(Ⅱ)--实验结果的动力学模拟

以文献[1]建立的张应力引起的非平衡晶界偏聚动力学方程模拟了Shinoda T等的磷在钢中的应力时效实验结果和Misra R D K的硫在钢中的应力时效实验结果，模拟结果与实验结果互相吻合。通过模拟发现，张应力使磷-空位复合体以及硫-空位复合体在钢中的扩散系数均增加3个数量级，且磷原子和硫原子的扩散系数分别降低3个和5个数量级。     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

基于湿度扩散理论的混凝土早期收缩分析

混凝土早期收缩开裂是加剧混凝土劣化并导致最终失效的一个重要因素．分析混凝土早期的自由收缩量值是进行收缩开裂研究的基础。为此，基于湿度扩散理论建立了混凝士早期的自生收缩与干燥收缩计算分析模型，经实例验证，计算结果与试验结果有较好的一致性。     

用保形样条方法求解非定常对流扩散方程

在欧拉-拉格朗日分裂方法的基础上,本文发展了一种固定网格上的欧拉-拉格朗日分裂方法.保形样条方法(SPSM)被用来解决倒特征线插值问题.通过求解几个有精确解的例子,说明SPSM方法的解是单调无振荡的,并且数值耗散也是比较小的.     

多台并行随机CIMS可靠性的扩散估计界

ＣＩＭＳ可靠性模型随机研究的突出特点是工作站的并行结构使系统的状态个数呈现指数级增大，同时，并行结构与有限的缓冲库相互交织在一起，这使系统状态呈爆炸趋势，显然，对系统作精确的分析与系统呈现的状态爆炸趋势构成了难以解决的矛盾，如何解决这一矛盾正是ＣＩＭＳ随机理论有待开发的重要课题。我们把扩散近似方法引入到多台并行的ＣＩＭＳ可靠性模型中，以简单的连续过程描述了具有状态爆炸趋势的复杂离散过程，给出了ＣＩ     

钢／铝合金液固相复合工艺的研究

通过正交试验研究了各工艺量数以钢／铝合金液固相复合性能的影响，最佳工艺条件为铝合金液体温度７９０℃，钢板表面处理为酸洗＋钢刷＋５％的氟钛酸钾助焊剂，复合压力为３９．２ＭＰａ，组织观察表面界面脆性化合物的形成是导致结合强度降低的一个重要因素。