Homogeneity characterisation of sintered (U,Gd)O2 pellets by X-ray diffraction

(U,Gd)O₂ sintered pellets are fabricated by different methods. The homogeneity characterisation of the Gd content seems to be necessary for a production control to qualify the process and the final product obtained. In this paper, we propose an analysis of the X-ray diffraction powder patterns through the Rietveld method, in which the differences between the experimental and the calculated data proposed from a crystalline structure model are evaluated. This result allows us to determine the cell parameters, that can be correlated with the Gd concentration, and the existence of other phases with different Gd contents.     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

甘三酯立体专一分析的研究：（Ⅱ）甘三酯立体专一分析方法初探

在第一部分综合讨论的基础上对甘三酯立体专一分析方法作了初步探讨。以液体油(菜油)及固体脂(猪脂)为基质,系统地研究了这一分析方法,取得了经验并补充了一些具体验证方法。分析液体油的结果与文献数据相一致,分析猪脂的结果欠佳,还存在一些问题需待进一步研究。     

Effects of Ca and Zr substitution upon structure and properties of Ba5LaTi3Ta7O30 low-loss dielectric ceramics

Effects of Ca and Zr substitution upon the dielectric properties of Ba₅LaTi₃Ta₇O₃₀ ceramics were investigated together with the structural characterization. All the samples of Ba₅La(Zr_xTi_1−x)₃Ta₇O₃₀ formed a filled tungsten-bronze structures, whereas the solid solution limit was determined as x=0.25 in (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀. Beyond this limit secondary phase of CaTa₂O₆ was detected and it would become the major phase for the Ca-rich compositions. The temperature coefficient of dielectric constant was improved with increasing Zr content while the dielectric constant decreased and the low dielectric loss varied little (in the order of 10⁻⁴). In the case of (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀, small temperature coefficient of dielectric constant could be obtained with increasing Ca content while the dielectric constant decreased significantly, and a small amount substitution of Ca for Ba induced decrease in dielectric loss.     

A comparative study of the gas sensing behavior of nanostructured nickel ferrite synthesized by hydrothermal and reverse micelle techniques

A comparative study of gas sensing behavior of nanocrystalline nickel ferrite synthesized by micro-emulsion and hydrothermal method to liquefied petroleum gas (LPG) is presented. Nanocrystalline nickel ferrite synthesized by hydrothermal method indicated higher electrical conductivity and gas sensitivity at low operating temperature compared to nanocrystalline nickel ferrite synthesized by reverse micelle technique. This difference in the gas sensing behavior can be attributed to the presence of more oxygen vacancies (i.e. non-stoichiometry) in the hydrothermally synthesized nickel ferrite. Incorporation of palladium had a catalytic effect and the operating temperature was significantly reduced in both the samples. The higher operating temperature of the reverse micelle nickel ferrite material makes the sensor response speed faster (∼10 s) compared to the hydrothermally synthesized material (∼1 min).     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.     

Grain growth kinetics in Dy-doped Bi0.5Na0.5TiO3 ceramics

Dysprosium-doped bismuth sodium titanate ceramics were prepared using the conventional mixed-oxide method. The amount of dysprosium used was varied from 0 to 2 at.%. The mixed powders were calcined at 800 °C and checked for phase purity using X-ray diffraction technique. The calcined powders were then cold-pressed into pellets and sintered at 1050 °C for the time ranging from 2 to 48 h. The ceramics were checked for phases and microstructures using an X-ray diffractometer and a scanning electron microscope, respectively. The analysis showed that undoped BNT ceramics sintered at longer time exhibited a significant grain growth with non-uniform grain size distribution and shape. The Dy-doped BNT however showed a much more limited grain growth behavior, resulting in smaller grain size and more equiaxed grain shape. It was also found that all Dy-doped BNT ceramics sintered at 48 h possessed lower porosity than those sintered for shorter time.     

Potential of vibro-milling technique for preparation of electroceramic nanopowders

The potential of the vibro-milling technique as a simple method to obtain usable quantities of single-phase electroceramic powders with nanosized particles was examined. A detailed study considering the role of both milling time and firing condition on phase formation and particle size of the final product was performed. The calcination temperature for the formation of the desired phase was lower when longer milling times have been applied. More importantly, by employing an appropriate choice of the milling time and calcination condition, high purity electroceramic nanopowders have been successfully prepared with a simple solid-state reaction method.