Application of piece‐wise linear weight functions for 2D 8‐node quadrilateral element in contact problems

The present study is a continuation of our previous work with the aim to reduce problems caused by standard higher order elements in contact problems. The difficulties can be attributed to the inherent property of the Galerkin method which gives uneven distributions of nodal forces resulting in oscillating contact pressures. The proposed remedy is use of piece‐wise linear weight functions. The methods to establish stiffness and/or mass matrix for 8‐node quadrilateral element in 2D are presented, i.e. the condensing and direct procedures. The energy and nodal displacement error norms are also checked to establish the convergence ratio. Interpretation of calculated contact pressures is discussed. Two new 2D 8‐node quadrilateral elements, QUAD8C and QUAD8D, are derived and tested in many examples, which show their good performance in contact problems. Copyright © 2004 John Wiley & Sons, Ltd.     

Influence of ion bombardment on the properties and microstructure of unbalanced magnetron deposited niobium coatings

The effect of the ion bombardment to unbalanced magnetron deposited, approximately 1.5 and 4.5 μm thick, Nb coatings have been investigated as the bias voltage was varied from U_B=−75 to −150 V. Increasing bias voltage increased the hardness of the coating from 4.5 to 8.0 GPa. This was associated with residual stress and Ar incorporation into the Nb lattice. Strong {110} texture developed in the samples deposited at low bias voltages, while beyond U_B=−100 V a {111} texture became dominant. However, strong {111} texture was observed only with the thicker 3Nb coatings. Secondary electron microscopy investigation of the coating topography showed fewer defects in the thicker coatings. All coatings exhibited good corrosion resistance, with the thicker coatings clearly outperforming the thinner ones. Excessive bias voltages (U_B=−150 V) was found to lead to poor adhesion and loss of corrosion resistance.     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

Mechanical degradation of coating systems in high temperature cyclic oxidation

Cyclic oxidation tests were performed on a large variety of commercially available overlay coatings. The results of cyclic oxidation tests confirmed that the composition of the coating as well as the processing method of the coating can affect the life of the system. Coating life was determined by the time to coating penetration and initiation of substrate attack. As this work was part of a effort to evaluate the relative protectiveness of available coating systems for Industrial Gas Turbine applications at relatively high temperature, an extensive testing programme was undertaken. The different coatings were tested to visual failure. The results presented in this paper concentrate on the surface instability of the coating. Apart from usual oxidation of the coating an additional degradation mechanism was observed. A mechanical effect caused by the instability of the coating as a result of the difference in the thermal coefficient of expansion and mechanical properties between the substrate and coating. This effect, the so-called “rumpling” effect, resulted in a significant reduction in time to penetration and was in some systems the life controlling factor.     

筒体结构连续化模型的弹性动力时程分析

本文用连续化模型对高层筒体结构在地震作用下的动力时程反应进行分析．     

聚四氢呋喃及其下游产品的开发应用

本文论述了聚四氢呋喃技术进展、氨纶弹性纤维发展现状和国内外聚四氢呋喃产能和需求。     

高温润滑涂层设计的系统考虑

航天、航空、核能等尖端技术迫切要求使用耐高温润滑涂层，以保护金属构件的表面，增加发动机、推进器的工作效率和输出功率，８０年代国际摩擦学界根据工业和国防的需要将高温润滑涂层和耐磨材料定为摩擦学学科发展的重要研究方向之一。本文对高温润滑涂层设计中遇到的典型环境、涉及到的关键问题、未来发展的途径等问题作了阐述。     

高速微粒携基因侵入植物细胞的速度条件

本文围绕基因枪技术中用高速微粒向植物细胞中导入外源基因的速度条件，分析了其中的三个动力学过程：发射宏弹、加速微弹、侵入细胞．提出了气动撞击发射式基因枪中弹簧刚度应满足的条件；得到了一种用理论分析与试验测试相结合确定微弹出射速度的方法；找到了微弹侵入植物细胞的最小速度条件。从而为基因枪的设计提供了理论依据。     

Laminated beams subjected to transverse load

A simple elastic solution has been developed for predicting the shear stress distribution in a laminated beam subjected to a variety of transverse loading conditions. Photoelastic tests on composite models involving a single bonding layer have been used to validate the theory, and also to comment upon the significance of these results in interpreting the interlaminar shear strength and bending modulus of the simplest form of laminated strip.     

Development of Low-Oxide MCrAlY Coatings for Gas Turbine Applications

Advanced high-energy plasma systems are being used to achieve the benefits of the high-velocity oxy-fuel (HVOF) system without losing the inherent advantages of plasma for coating of gas turbine parts. MCrAlY coatings play a very important role in the performance and reliability of gas turbine components. One of the important considerations for next generation of gas turbines, which have more demanding conditions and need to withstand ever increasing operating temperatures, is that they should possess very low oxygen content levels in the coating. Low oxygen content coatings are applied by the expensive low-pressure plasma spray (LPPS)/vacuum plasma spray (VPS) technique for critical components in aero- and land-based gas turbines. This work deals with the development of low-cost LPPS equivalent coatings (having low oxygen content) using the high-energy high-velocity plasma spray (HEHVPS) gun and inert gas shroud. A comparison has also been made with CoNiCrAlY coatings by HVOF.