高压脉冲放电处理含氰废水的影响因素探讨

焦化废水中含有大量的氰化物,必须采取有效措施进行去除,传统去除方法运行成本高、操作复杂。提出了用高压毫微秒脉冲产生的非平衡等离子体处理含氰废水的方法,对其影响因素pH值、放电时间、气流量、放电条件等进行了大量的实验研究,结果表明:溶液初始pH值为9.09,放电2 h,放电电压46 kV时氰化物的去除率最高可达93.2%,氰化物质量浓度可降至0.26 mg/L。实验对比了放电与不放电氰化物的去除效果:相同条件下放电后氰化物的去除率大大提高,为焦化废水中氰化物的去除提出了一种新的方法。     

Gasification of polyethylene using steam plasma generated by microwave discharge

Gasification of polyethylene (PE) pellet was studied using atmospheric argon-steam plasma generated by microwave discharge and the feasibility of the process was examined. The experimental results showed that additional steam to argon plasma promoted the weight decrease of PE and enhanced the production of H₂, CO, CO₂ and CH₄. The results confirmed that the treatment of plastics with the steam plasma was effective to obtain synthesis gas.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

美国危险废物处理的领先尖端技术--等离子强化熔炉介绍

从工作原理、主体结构、工艺流程等方面，系统地介绍了当代处理危险废弃物的领先尖端技术——等离子强化熔炉，并结合实地考察，介绍了其工业化发展及其应用实例。     

离子束辅助沉积制备高功率激光薄膜的研究

综述了离子束辅助沉积技术在高功率激光薄膜制备中的应用研究进展.指出该技术在制备高激光损伤阈值的薄膜中存在的问题,即出现过高的堆积密度,会给薄膜带来杂质缺陷、化学计量比缺陷、损伤缺陷、晶界缺陷,制备薄膜的残余应力存在着压应力增加的趋势,会改变薄膜的晶体结构等.并指出了该研究领域的研究方向.     

水喷雾灭火系统在电信枢纽工程燃气锅炉房的应用

分析了燃气锅炉的火灾危险性和水喷雾用于燃气锅炉消防的灭火机理,提出了水喷雾灭火系统的设计参数的选择、系统的控制方法以及在设计中可能涉及到的问题和注意事项,并结合工程实例进行了探讨。     

一种基于bit位的运动补偿方法

本文讨论了等离子体显示屏所特有的在显示运动画面时出现的伪轮廓线现象，对产生的原因进行了分析并给出了软件模拟的结果。在此基础上，提出了一种基于bit位的运动补偿方法来改善运动图像的画面质量，同时根据人眼的视觉特征对补偿方法做了进一步的优化。最后对基于bit位的运动补偿方法进行了比较和验证，结果表明基于bit位的运动补偿方法可以基本消除运动画面的伪轮廓线现象。     

The Structure of Clusters and Jets of Pulsed Plasma Expanding into Vacuum

The space-time distribution of the basic kinetic parameters of a plasma is experimentally determined under conditions of expansion of plasma clusters and jets into vacuum. It is demonstrated that the dynamics and structure of plasmoids injected by pulsed erosion plasma accelerators of the electrothermal type are characterized by two successive stages or two modes of acceleration, namely, the Joule heating of electrons in the initial region of the path and the collisionless expansion of rarefied plasma.     

制备单根大重量喷涂钼丝的生产研究

全面系统地介绍了“大坯料轧制开坯-大加工率变形-长线拉伸”制造喷涂钼丝的工艺。重点阐述了Y370、Y250型三辊连轧机实现一火轧制开坯和长线拉伸增加在线碱洗工序对提高喷涂钼丝内部组织结构和外部表面质量的影响。分析了工艺中出现的问题，提出了相应的解决办法。