烧结机配料系统研究与应用

本文分析了烧结配料系统目前存在的问题,并进行了优化改进。使得配料生产效率得到了明显的提高,同时降低了故障率。改造后仪表的功能得到充分利用,生产能稳定进行。     

交流电机绕组分布系数推导方法的研究

对交流电机绕组分布系数推导的代数法进行了详尽描述,并对代数法与几何法进行了比较。     

JJF-130m^3机械搅拌式浮选机工业试验研究

系统地研究和分析了大型机械搅拌式浮选机—JJF-130m3型浮选机的带矿性能和工业应用效果,针对现场的矿石性质、药剂用量和磨矿细度,制定了试验内容,测定了浮选机的矿浆悬浮能力、对不同粒级矿物的分选效果,并对累计工业试验指标进行了对比分析。试验结果表明JJF-130m3型浮选机槽内矿浆粒度分布均匀,没有粗、细颗粒分层现象,浮选机矿粒悬浮能力好,液面不翻花。工业试验累计指标与国外某品牌同类型同容积浮选机相比:在原矿品位相当的情况下,精矿品位高0.22%,尾矿品位低0.07%,回收率高3.82%,浮选效率高3.70%,浮选机浮选性能优于国外某品牌浮选机,证明浮选机浮选效果好。     

叉车门架断裂原因分析

采用化学成分分析、力学性能测试、金相检验以及断口分析等方法对某叉车门架断裂的原因进行了分析。结果表明:由于在门架焊缝收弧部位存在凹坑缺陷和裂纹,形成缺口效应,产生缺口应力集中,加之门架的不对称工作应力的作用,最终造成门架发生了疲劳断裂失效。     

Grain boundary microstructure and fatigue crack growth in Allvac 718Plus superalloy

The correlation between grain boundary microstructure and fatigue crack growth with hold-times was investigated for two conditions of the superalloy Allvac 718Plus; a Standard condition with the recommended distribution of grain boundary phases and a Clean condition with virtually no grain boundary phases. Fatigue testing was performed at 704 °C using 10 Hz cyclic load with intermittent hold-times of 100 s at maximum tensile load. Microstructural characterization and fractography were conducted using scanning- and transmission electron microscopy techniques. Auger electron- and X-ray photoelectron spectroscopy techniques were used for oxide analyses on fracture surfaces. It was found that in the Standard condition crack growth is mostly transgranular for 10 Hz loading and intergranular for hold-times, while for the Clean condition crack growth is intergranular in both load modes. The lower hold-time crack growth rates in the Standard condition are attributed to grain boundary δ-phase precipitates. No effect of δ-phase was observed for 10 Hz cyclic loading crack growth rates. Two different types of oxides and oxide colours were found on the fracture surfaces in the Standard condition and could be correlated to the different loading modes. For cyclic loading a bright thin Cr-enriched oxide was dominate and for hold-times a dark and slightly thicker Nb-enriched oxide was dominant These oxide types could be related to the oxidation of δ-phase and the matrix respectively. The influence of δ-phase precipitates on crack propagation is discussed.     

ZDRH-3000智能集中润滑系统在265m2烧结机的应用

介绍了ZDRH-3000智能集中润滑系统的主妥功能及在265m。烧结机上应用的效果。     

A robust design to reduce variability in glass container inspection

This article presents research efforts made to assist a Fortune 500 glassmaker in reducing the variability of its automated visual inspection systems in assessing product quality. Through interviewing line workers, engineers and managers, and direct observations of the inspection process possible causes leading to large variability observed in the inspection process were identified. Responding to these findings, solutions related to equipment setup, job changes, and operational procedures were suggested in order to minimize the inspection process variations as well as to improve the replicability of the inspection stations. Additionally, a unique statistical experiment was conducted to analyze how three factors (namely, operator, defect size, and threshold value used) would affect the mean of the defective ratio. A robust design aiming at controlling these variations was then given to optimize the system's performance.     

短纤维链板式松弛热定型机流场的研究

分析了链板式松弛热定型机的结构及运行特点;通过对链板式松弛热定型机的冷态测试实验,获得了热定型机内部流场气流的速度分布数据,以探讨热定型机内部流场的特点。结果表明:在纤维层上部存在着明显的气流不均匀现象,匀风板上部具有高速气流区;指出热定型风板开孔不合理,导致纤维层上部气流分布不均匀,气流短路使得散热器下部流场分布不均匀;提出改善热定型机匀风板的开孔率,可实现均匀布风的初步方案。     

加工时间线性递减的链约束单机排序问题

讨论了工件的加工时间是开工时间的线性递减函数、工件之间有平行链约束的单机排序问题.对于链可中断和不可中断两种情况,给出了极小化总完工时间的最优算法.     

新型电励磁磁通切换电机励磁绕组结构分析

励磁绕组连接方式对电励磁磁通切换电机电磁特性影响很大。对所提出的2种新型电励磁磁通切换电机,分析了其工作模式和“磁通切换原理”,利用有限元分析方法比较了2种电机的电磁特性：定子磁链、反电势、气隙磁密、定位力矩、电磁转矩、转矩密度。重点比较了励磁绕组连接方式对电机漏磁和功率密度的影响。结果表明,电励磁磁通切换电机具有较高正弦度的双极性磁链和全周期工作模式,适合运行在无刷交流场合。拓扑2具有更小的漏磁和更高的励磁电流利用率,其转矩密度为拓扑1的2倍。分析结果为所提出电励磁磁通切换电机在航空起动／发电机系统、风力发电系统等领域的应用提供了理论背景。