提高连续油管使用寿命的方法

从采用软件跟踪疲劳寿命 ,截断法 ,变径连续油管 ,反转使用连续油管 ,防止连续油管损伤 ,合理配置设备 6个方面讨论了控制管串疲劳 ,提高连续油管使用寿命的方法 ,并得出结论 :控制管串疲劳的方法中 ,最有效的方法是实际作业截断法。指出要尽量减少连续油管在带内压下工作 ,也要研究开发降阻性能好的工作液 ,以延长连续油管使用寿命、降低作业风险。     

用于一维图像识别的支撑矢量机方法

研究了支撑矢量机的分类机理,并利用支撑矢量机对雷达目标一维像进行了识别.识别的结果表明了该方法的优越性,并显示它可以对残缺不全的样本进行识别.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

Improvement of Air-Distributing System of the Pneumatic Impact Machines for Trenchless Technologies

The process of actuation is considered for the inertial element in the improved air-distributing system of pneumatic puncher whose dimensionless parameters are determined.     

轮式工程机械的行驶平稳性

根据振动理论建立了振动力学模型,并用等效刚度方法分析研究了弹性悬挂轮式工程机械行驶平稳性和振动特性。     

一种简易的容积式灌装机

介绍了一种用于液体产品分装 ,易于使用的容积可调式灌装机的工艺原理及主要部件的结构     

基于支持向量机的岩爆识别模型

岩爆的发生受多种因素的影响,这些因素关系错综复杂,以不同的特征和组合对岩爆产生综合影响,为科学、充分地利用现有的有限工程资料,本文从地下洞室围岩最大切向应力、岩石的单轴抗压强度和抗拉强度以及岩石冲击倾向指数四个主要因素出发,提出了基于支持向量机的岩爆识别模型,较好地解决小样本、非线性、高维数、局部极小点等的实际问题。     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

触摸输入技术探析

本文扼要概述触摸输入的４种技术，及其应用与性能比较。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.