抗生素生产过程补料时机的Fuzzy识别与预报

本文就抗生素发酵生产过程,提出了一种补料时机的Fuzzy识别、预报的建模方法,并根据20m~3发酵罐工业数据的分析,选取了以总糖、总糖变化率、氨基氮和氨基氮变化率四个主要参数作为输入集因素,运用本文提出的方法,建立了一个实际的抗生素发酵生产过程补料时机的 Fuzzy 识别、预报模型。经现场调试效果良好,与富有经验的行家相比,准确率达90%以上。     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

十三陵蓄能电站上水库自动监测系统的设计及运行

由于十三陵蓄能电站上水库地处蟒山之巅，所在山体地质条件复杂。施工期埋设了大量的监测仪器，原有人工监测系统效率低、资料分析的同步性差。2002年5月，对其进行了自动化改造，现已有一套符合其特点的自动化监测系统。十三陵上水库水工建筑自动监测系统已正常运行了三年，同时也存在着问题，有待于进一步的探讨和改进。     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Stepwise-Graded Si3N4–SiC Ceramics with Improved Wear Properties

The processing of stepwise graded Si₃N₄/SiC ceramics by pressureless co-sintering is described. Here, SiC (high elastic modulus, high thermal expansion coefficient) forms the substrate and Si₃N₄ (low elastic modulus, low thermal expansion coefficient) forms the top contact surface, with a stepwise gradient in composition existing between the two over a depth of ∼1.7 mm. The resulting Si₃N₄ contact surface is fine-grained and dense, and it contains only 2 vol% yttrium aluminum garnet (YAG) additive. This graded ceramic shows resistance to cone-crack formation under Hertzian indentation, which is attributed to a combined effect of the elastic-modulus gradient and the compressive thermal-expansion-mismatch residual stress present at the contact surface. The presence of the residual stress is corroborated and quantified using Vickers indentation tests. The graded ceramic also possesses wear properties that are significantly improved compared with dense, monolithic Si₃N₄ containing 2 vol% YAG additive. The improved wear resistance is attributed solely to the large compressive stress present at the contact surface. A modification of the simple wear model by Lawn and co-workers is used to rationalize the wear results. Results from this work clearly show that the introduction of surface compressive residual stresses can significantly improve the wear resistance of polycrystalline ceramics, which may have important implications for the design of contact-damage-resistant ceramics.     

高密度聚乙烯6300M和2480的耐环境应力开裂性能研究

研究了成型塑料管材的两种牌号的高密度聚乙烯(HDPE)6300M和2480的耐环境应力开裂(ESCR)性能。研究中采用的测试方法为一般弯曲试片法、在管上取样的弯曲试片法和恒定压应变法-压缩环法。根据两种材料测试结果及与其他牌号HDPE测试数据比较,对他们的ESCR进行评价,并讨论和解释了HDPE结构参数,ESCR与韧性形变和脆性断裂之间的联系。     

市内通信电缆绝缘电阻特殊要求的实现和措施

本文对市内通信电缆的各生产过程进行分析、研究和控制 ,从而提出了解决绝缘电阻特殊要求的方法 ,以及改进的措施。     

Thermal Shock Behavior of Porous Silicon Carbide Ceramics

Using the water-quenching technique, the thermal shock behavior of porous silicon carbide (SiC) ceramics was evaluated as a function of quenching temperature, quenching cycles, and specimen thickness. It is shown that the residual strength of the quenched specimens decreases gradually with increases in the quenching temperature and specimen thickness. Moreover, it was found that the fracture strength of the quenched specimens was not affected by the increase of quenching cycles. This suggests a potential advantage of porous SiC ceramics for cyclic thermal-shock applications.     

高耐水高光泽苯丙乳液研究

采用反应型乳化剂AMPS及常规乳化剂合成了一种高耐水高光泽苯丙乳液。讨论了合成工艺、引发剂、乳化剂、AMPS等对乳液的影响。乳液中乳化剂含量 0 .9% (占单体 ) ,耐水性 14 4h不变白。