模具材料的硅硼氮共渗

介绍５ＣｒＮｉＭｏ钢模具材料经硅硼氮共渗后，可使其耐磨性得到明显改善。     

海岛型阳离子交换纤维的研究

阐述了海岛型阳离子交换纤维的制备方法,对交联、磺化过程中的硫酸浓度,多聚甲醛的添加量,反应时间,反应温度等对离子交换容量的影响进行了讨论。     

介孔材料化学改性研究进展

综述了介孔材料化学改性目的，改性原理以及改性方法。介孔材料的化学改性包括对材料骨架的修饰以及对孔道表面的功能化，介孔材料表面自由硅醇键、双羟基硅醇踺是化学改性的基础，利用疏水性物质改性可以提高材料的水热稳定性，引入催化活性组分可以提高催化性能，利用具有特定官能团的硅烷偶连剂改性，则能够实现特殊的目的。详述了化学改性方法，包括元素取代法、共价键移植法和有机硅烷偶连法。元素取代法是对分子筛骨架结构的修饰，共价键移植法是一种不引起孔道结构破坏且非常有效的骨架修饰方法，对介孔材料表面进行有机硅烷偶连剂法修饰改性主要有两种途径：即共沉淀法和后移植法。     

Synthesis of nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries

A novel process was proposed to synthesize nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries. The preparation started with the dissolution of SbCl₃ and polyacrylonitrile (PAN) in dimethylformamide (DMF) solution, followed by the addition of KBH₄ to reduce Sb³⁺ in the solution. The Sb composite was obtained by pyrolysis of the Sb/PAN mixture that precipitated out when the DMF solution was added by plentiful water. The TEM analysis showed that about 100-200 nm Sb particles were embedded by the pyrolyzed PAN, which provided a conductive matrix to relieve the morphological change of Sb during electrochemical cycling. As-prepared composite presented good cycleability for lithium storage. The proposed process paves an effective way to prepare high performance alloy based composite anode materials for high performance lithium-ion batteries.     

β晶型成核剂改性聚丙烯纤维研究

研究了含 0 .2 5 %β晶型成核剂 (酰胺化合物 )的聚丙烯 Z3 0 S及其纤维的力学性能、晶型结构和微观形态。通过纺丝 -拉伸实验和力学性能测试、广角 X射线衍射分析、SEM观察 ,发现成核改性后生成了β晶型聚丙烯 (K值约为 75 .3 % ) ,抗冲性能大幅度提高。β晶型聚丙烯在纺丝卷绕过程中发生了β晶型→α晶型转变 ,纤维中产生约 10 %微孔隙 ,改性纤维的力学性能有所降低。     

SBS改性沥青

介绍了沥青的特性，改性沥青的种类与性能，以及丁苯嵌段共聚物改性沥青的相容性，溶胀性，分散性等方面的研究进展，并提出了发展建议。     

PHENOL RECOVERY WITH SLM USING “CYANEX 923”

The study of the phenol separation-concentration process with the hollow fiber supported liquid membrane technology has been performed. Mixtures of kerosene and CYANEX 923 were used as liquid membrane. The extractant CYANEX 923 is characterized by a high phenol selectivity and an extremely low solubility in the aqueous phase. The introduction of CYANEX 923 in the membrane composition decreases the extractant losses from the pores of the support.

The phenol separation and simultaneous concentration process has been checked. The influences of the initial concentration of phenol in the feed solution and sodium hydroxide in the stripping phase and the membrane composition on the separation rate have been investigated in a single-pass mode. The analysis of the membrane composition influence has been performed according to the steady-state mass transfer conservation equation and the associated boundary conditions, leading to the mass transfer parameters of the process     

二甲基硅油及其表面活性剂在化纤生产中的应用

综述了二甲基硅油及其表面活性剂在化纤油剂中的应用 ,化纤油剂应具有的高平滑性、高耐热等特性 ;介绍了改善油剂的综合性能及硅油表面活性剂用来提高纤维的可纺性等性能的方法。建议我国应尽快开发研制含硅油的化纤油剂     

活性炭吸附法处理麦麸膳食纤维废水的研究

采用活性炭吸附的方法来处理麦麸膳食纤维废水。实验结果表明,当活性炭的投入量为160 g/L,接触时间为20 m in,温度为55℃,pH值在小于5的条件下能有效处理该废水,CODC r的去除率最高达96.89%,BOD5的去除率最高达96.61%。     

微细纤维发展概况与趋势

介绍了微细纤维发展概况,包括生产工艺,纤维性能,最终用途以及当前的发展趋势。并对我国发展微细纤维提出建议.