四辊铝箔轧机预控参数在线整定

介绍Ф210mm/Ф500mm× 800mm四辊液压轧机厚度预控系统中采用人机界面实现参数在线调整的方法,能大大提高预控参数的控制精度,减少轧机产品的厚度误差,是厚度自动控制的一项创新.     

磷氮阻燃腈纶结构性能及阻燃机理研究

研究了含磷酸二氢铵和脲复合阻燃剂的共混阻燃腈纶的结构和性能。研究表明，在纤维成形加工过程中，部分阻燃剂聚合生成聚磷酸铵和聚脲，阻燃剂以微粒状均匀分散并包埋在纤维内部；阻燃剂的加入使纤维高序区大分子间等距离排列的规整性和片状结构单元等距离平行排列的程度降低，热稳定性亦略有下降；但纤维的宏形态结构及物理机械性能没有明显变化；磷氮阻燃腈纶具有良好的阻燃性和阻燃耐久性，经碱洗２０次、水洗３０次后，阻燃剂的磷和氮的保留率分别高达８２．９％和８９．５％，纤维的ＬＯＩ值仍在２６％以上。     

The Structure of the Irreversibly Bound Adhesion Promoter-Substrate Interfacial Layer of γ-Aminopropylsilanetriol on Crystalline Si, as Measured by XPS and FTIR

The irreversibly bound interfacial layer deposited by the γ-aminopropysilanetriol adhesion promoter onto a crystalline silicon substrate, which remains even after profuse washing, was found by XPS to have resulted from the fragmentation and rearrangement of the original γ-aminopropylsilanetriol molecule. A mechanism is proposed, involving the homolytic scission of the terminal N-C bond. One of the subsequent reactions is believed to involve hydrogen loss by abstraction and the formation of a terminal vinyl group, which bonds to the substrate. Support for this mechanism is found in IR spectroscopy of this layer.     

PHENOL RECOVERY WITH SLM USING “CYANEX 923”

The study of the phenol separation-concentration process with the hollow fiber supported liquid membrane technology has been performed. Mixtures of kerosene and CYANEX 923 were used as liquid membrane. The extractant CYANEX 923 is characterized by a high phenol selectivity and an extremely low solubility in the aqueous phase. The introduction of CYANEX 923 in the membrane composition decreases the extractant losses from the pores of the support.

The phenol separation and simultaneous concentration process has been checked. The influences of the initial concentration of phenol in the feed solution and sodium hydroxide in the stripping phase and the membrane composition on the separation rate have been investigated in a single-pass mode. The analysis of the membrane composition influence has been performed according to the steady-state mass transfer conservation equation and the associated boundary conditions, leading to the mass transfer parameters of the process     

微细纤维发展概况与趋势

介绍了微细纤维发展概况,包括生产工艺,纤维性能,最终用途以及当前的发展趋势。并对我国发展微细纤维提出建议.     

三箱式纺丝技术生产PET/PA6复合纤维

介绍了采用三箱式纺丝技术生产PET/PA6复合纤维的设备及工艺。重点对纺丝箱体、纺丝温度控制进行了详细的讨论。     

世界化纤发展趋势

对纤维的需求不断增长，天然纤维缺口将愈来愈大，均为化纤发展带来了机遇。化纤工业竞争激烈，主要趋势为扩大规模提高效率。无人化、环保化也是一种趋势。同时也发展了一些与下游名牌产品联系在一起的小型专业厂．高技术、高性能纤维发展较快．在技术方面，认为纤维超细化、废弃物回收重新纺制纤维，注意环保，设备增容、高效化，高性能纤维开发等是主要趋势．     

试论我国锦纶生产发展方向

回顾了锦纶发展简史，综述了国内锦纶生产现状，并论述了我国锦纶生产发展方向，必须大力发展原料工业；加快老企业的设备改造；使其达到规模经济，大力发展差别化、高附加值、功能性纤维。同时，提出了锦纶各品种的发展趋向。     

Boundary layer model for char combustion and gasification

A non-steady boundary layer model is developed for numerical simulation of combustion and gasification of a single shrinking char particle. The model considers mass and energy conservation coupled with heterogeneous char reactions producing CO and homogeneous oxidation of CO to CO₂ in the boundary layer surrounding the char particle. Mass conservation includes accumulation, molecular diffusion, Stefan flow and generation by chemical reaction. Energy conservation includes radiation transfer at the particle surface and heat accumulation within the particle. Simulation results predict experimentally measured conversion and temperature profiles of a burning Spherocarb particle in a laminar flow reactor. Effects of bulk oxygen concentration and particle size on the combustion process are addressed. Predicted particle temperature is significantly affected by boundary layer combustion of CO to CO₂. With increasing particle size, char gasification to char combustion ratio increases, resulting in decreasing particle temperature and increasing peak boundary layer temperature.     

碳纤维经氧等离子/KH550处理后的表面形态和结构

碳纤维(CF)表面经氧等离子、KH550和 LiAlH_4处理后,其物理和化学性能得以改善.由于提高了 CF 和树脂间的联结,使 CF 复合材料的层间剪切强度提高50%以上,在湿热下的强度保留率达94%以上.使用纤维接触角测定仪,SEM 和 XPS 等对 CF 表面的浸润性、形态和化学组成进行了研究.实验指出:CF 经等离子和 KH550处理后,其临界表面能有了提高;CF 本身仅受氧离子刻蚀,故其拉伸强度的损失小于其他处理方法.