降膜波动特性的研究

本文提出了一种测定膜厚的新方法－双电导探针法，测定了高湍流降膜的厚度沿降膜管管程的变化情况，探讨了径向平均膜厚及膜厚的概率密度分布沿管程的变化规律，证明降膜的波动特性同时受到液相雷诺数和管程的影响。并对平均膜厚和液相雷诺数作了经验关联，得出NT＝（δ^ )^2/3 [8.92(ReL/4)^5/2 6.0×10^-6(ReL/4)^9/2]^2/15。     

混杂方式对CF/UHMWPEF混杂复合材料力学性能的影响

本文通过碳纤维/超高分子量聚乙烯纤维混杂复合材料的力学性能试验及结果比较,分析了三种混杂方式对该类复合材料的力学性能的影响.结果表明,不同混杂方式的碳纤维/超高分子量聚乙烯纤维复合材料具有各自的力学特点.     

Studies of microhardness and mar resistance using a scanning probe microscope

Scanning probe microscopy (SPM) is in a period of rapid development. It shows great promise for characterizing coating surfaces. This paper describes modification of an SPM so that it can be used to mar the surfaces of coatings under controlled conditions and to characterize the mars. Mar resistance of coatings is analyzed in terms of a ‘three response, two mechanism model.' The three responses (fracture, elastic, and plastic) can be measured quantitatively using the SPM. Of the three responses, only two (fracture and plastic deformation) are marring mechanisms – elastic deformations recover instantaneously. In some cases mars resulting from plastic deformation may recover slowly with time or with immersion in water; this phenomenon is attributed to viscoelastic creep. Microhardness is also measured with the modified SPM. Some thermoset coatings appear to be substantially harder near their surfaces than in the mass of material, and such materials may respond quite differently to stress applied at different levels near the surface. This finding has important implications for all coating properties that are strongly influenced by the surface. A quantity called ‘micro mar resistance' is defined. It may be useful for comparing different coatings under specified conditions of marring. However, there can be no single quantity that expresses ‘mar resistance' of a coating under all conditions.     

PE/PP皮芯型复合超短纤维生产技术

本文从原丝质量控制、原料选择、油剂的选用和工艺条件等方面介绍了PE/PP(聚乙烯/聚丙烯)皮芯复合超短纤维生产技术，指出分散性是超短纤维最主要的控制指标，3mm纤维是超短纤维的发展趋势．     

短纤维/橡胶发泡复合材料的微观结构及拉伸破坏机理

对锦纶短纤维增强的NR发泡材料的微观结构及拉伸破坏行为进行了研究，并分析了其破坏机理。采用未处理短纤维增强的NR发泡材料中短纤维成为泡孔的成核点，并大部分悬空在泡孔中，拉伸破坏时泡壁与短纤维结合处容易出现应力集中，成为裂纹的起始点，失效时短纤维大部分被抽出；预处理短纤维能与橡胶基体之间产生良好的粘合，从而处于橡胶基体中。其短纤维增强的NR发泡体拉伸产生的裂纹扩展时遇到纤维，纤维能起到承载应力、使应力转向、阻止裂纹扩展的作用，一定程度上改善了复合材料的拉伸强度等物理性。     

LDA Measurements on a Turbulent Gas/Liquid/Fibre Suspension

Detailed continuous phase flow measurements (mean and RMS velocities) by Laser Doppler Anemometry (LDA) of a turbulent gas/fibre/liquid suspension in a rotary shear tester have been performed with simultaneous torque measurements. The model system comprises a refractive‐index matched suspension in the 4‐12% wt. range with gas contents up to 15% vol. The two transition points, found by Andersson and Rasmuson (2000), were detected also with gas present and appear at higher impeller speeds with increasing gas and fibre concentrations. Plotting RMS and mean velocities versus impeller speed and power input, it is found that both decrease with increasing gas and fibre contents.     

预处理短纤维对VMQ/EPDM共混导电橡胶某些性能的影响

研究了预处理短纤维用量对乙炔炭黑填充甲基乙烯基硅橡胶（ＶＭＱ）／ＥＰＤＭ共混硫化胶拉伸、撕裂、耐屈挠疲劳和导电性能的影响。实验结果表明，加入适量短纤维对ＶＭＱ／ＥＰＤＭ体系有一定的补强作用；纤维用量较大时，导电性能下降。加入４．０份左右的预处理短纤维，可使ＶＭＱ／ＥＰＤＭ共混导电橡胶获得良好的物理机械性能和导电性能     

远红外腈纶纤维的研制

分析了远红外纤维保暖的机理,确定了试验流程及工艺条件,分析产品中远红外素的分散性,远红外素对原液粘度的影响,远红外纤维的性能以及远红外纤维的发射率.     

剑麻纤维／酚醛树脂复合材料研究

本文采用碱处理、硅烷偶联剂处理、化学接枝和热处理等物理化学方法，对剑麻纤维进行改性。研究了改性后短剑麻纤维／酚醛树脂复合材料的弯曲性能、无缺口冲击强度和布氏硬度，借助扫描电子显微镜观察了复合材料的弯曲断口形貌，并研究了剑麻纤维的不同处理方法对复合材料耐水浸泡性的影响。结果表明：剑麻纤维经硅烷偶联剂处理后，能有效改善刚性的剑麻纤维与脆性的酚醛树脂基体之间的粘结，从而提高了复合材料的综合力学性能，剑麻     

混酸冲洗滤盘的可行性

湿法磷酸生产中，均以水为介质冲洗倾覆盘式真空过滤机的滤盘，为实现系统的污水零排放，提高倾覆盘式真空过滤机的生产能力，提出以回磷酸和硫酸配制成混酸去冲洗滤盘的方法。分析了采用该方法的诸多优点及注意事项，指出安全生产问题须认真落实。