L520型智能中子仪测定农田土壤含水量的标定研究

通过对L520型智能中子仪测定农田土壤含水量的标定研究，在试验区草甸土类型的土壤中，在0～100cm的土层中得到了一条标定土壤含水量的回归直线，用此法测定土壤含水量较重量法快捷方便且误差小。     

小剂量辐照小鼠胸腺细胞膜流动性的变化

报道了以茈为荧光探针,探讨小剂量~(60)Co γ射线照射后小鼠胸腺细胞膜流动性的变化。结果表明,剂量在0.25-1.00Gy范围,胸腺细胞膜流动性降低与剂量之间呈明显线性关系。从0.50Gy起,辐照组荧光强度比值I_1/I_2与I_3/I_2与对照组的比较存有显著差异(P<0.05)。提示淋巴细胞膜流动性的变化可作为小剂量辐照早期效应的敏感指标。     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

扫描探针制备技术的研究现状及发展

探讨了近几年来探针制备技术的发展和趋势,分别就探针检测性能的改进、探针结构、探针检测功能拓展及多通道信息采集组合探针等几方面,对相关制备技术的方法、特点以及相应检测条件、适用环境展开讨论,这些方面反映探针制备技术正朝着尖锐化、多样化、功能化和组合方向发展。     

光纤光栅视觉系统

利用光学衍射原理，研制成了光纤光栅衍射屏，并与计算机神经网络相结合，开发了了一种识别立体形状的视觉系统。本文介绍了光纤光栅的设计原理及计算方法，给出了系统的总体结构及工作原理，完成了三棱 柱，三棱锥、四棱柱，四棱锥和球等立体形状学习与识别，并讨论了实验结果。     

六通道瞬态光学高温计

六通道瞬态光学高温计是在可见光和近红外光谱范围内 ,把光源的热辐射取出六个波段进行测量。每个波段信号通过各自的光纤传输、光电倍增管探测和记录仪器记录。系统的时间分辨率小于 30 ns,冲击温度测量范围为 2 30 0～ 90 0 0 K,测量误差小于 5 % ,给出了以碘化钠、硝基甲烷和空气为样品的若干实验结果     

聚合物电解质PEO全固态电致变色窗

本文用聚合物ＰＥＯ的锂盐络合物作电解质制作全固态电致变色窗，讨论了器件的特性，以及工艺条件的影响。     

组合式光纤流量传感器

提出了一种新型的组合式光纤流量传感器，介绍了它的工作原理，详细讨论了光脉冲转换器的设计要点，据此设计了传感头，并给出了它的实验结果。     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.