Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

超音速燃气射流非定常波系的数值研究

根据ＭＵＳＣＬ格式的基本思想，对格式进行了部分修改，数值模拟了超音速燃气射流流场的结构和发展过程。给出了流场谐波系的变化趋势，得到了流场达到稳定状态的时间和稳定后的流动图形。     

烧结NdFeB合金中的夹杂物

使用金相显微镜、扫描电镜及Ｘ射线能谱和波谱观察并分析了ＮｄＦｅＢ烧结材料中夹杂物的形态、数量和组成。磁粉制备后立即烧结的ＮｄＦｅＢ磁体中的夹杂物是氧化钕；而在不同环境条件下放置后的ＮｄＦｅＢ粉再烧结的材料中发现，除了氧化钕的夹杂物外，还有钕的氮化物及钕的氮氧复合夹杂物。同时还论讨了这些夹杂物对于ＮｄＦｅＢ材料磁性能的影响。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

PP／SiO2／SBS共混复合材料性能的研究

通过加入增强剂、增韧剂、抗氧剂等添国剂可改善聚丙烯力学性能。以ＳｉＯ２为填料，丁苯橡胶（ＳＢＳ）为增韧剂，探讨ＳｉＯ２、丁苯橡胶含量对共混体系强度、韧性的影响，结果表明，在ＳＢＳ含量大于５％、ＳｉＯ２一小于１０％的范围内，可使ＰＰ／ＳｉＯ２／ＳＢＳ复合的拉伸弹性模量和冲击强度明显提高，其力学性能均为均衡。     

给水流量控制系统仿真辅助设计

本文将给水流量系统规范化，给出静、动态数学模型，通过计算机仿真计算建立起设计参数Ｓ与系统特性间关系数据库，这些数据可用于控制系统辅助设计。本文还介绍了在Ｓ较小时自动补偿系统增益和时间常数的自适应控制方法并给出仿真结果。     

A modified flow enforcement technique for ATM networks

In ATM networks the requirement of providing the negotiated Quality of Service (QOS) needs an efficient flow enforcement technique that will result in preventive congestion control. A very effective technique is the Exponentially Weighted Moving Average (EWMA) method. In this paper, we have suggested improvements to the EWMA and call it the Enhanced EWMA (EEWMA). Simulation results show that the EEWMA is consistently better than the EWMA in most of the situations. We present comparisons of cell loss under various conditions. No theoretical analysis is presented.     

应用粒子动态分析仪研究水力旋流器流场

利用粒子动态分析仪(PDA),对水力旋流器内固相颗粒流场做了全面的测定,得出水力旋流器内固相颗粒的流态、浓度及粒度分布,为进一步查清水力旋流器的工作机理提供了重要理论依据。     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

氢电弧等离子体法制备的纳米镍铈粒子的催化特性

利用氢电弧等离子法制备具有储氢特性纳米镍铈粒子，并在气相苯加氢反应中研究了其催化特性，发现其催化活性与储氢特性及表面层中ＮｉＣｅ合金存在有关，且具有高的选择性和热稳定性，这与纳米粒子独特的结构及铈的加入有关。