甲酸甲酯合成与转化的催化技术

本文评述了甲酸甲酯(MF)合成与转化的催化技术,展示了从MF出发发展C_1化学的可能途径,在MF的合成方面详细地分析了从甲醇出发的羰化法、脱氢法和氧化法催化技术,简介了我们的有关研究工作。     

Viscoelastic, Thermal and Mechanical Properties of Dicyclopentadiene Bisphenol Diyanate Ester / Epoxy Co-polymers

Summary Dicyanate ester containing dicyclopentadiene cycles and epoxy co-polymers were prepared by copolymerization between epoxy and dicyclopentadiene bisphenol cyanate esters (DCPDCE). Viscoelastic properties of the co-polymers were characterized by the technique of dynamic mechanical analysis (DMA), which indicated that the introduction of E51 in the co-polymers would effectively improve the toughness of DCPDCE, while the thermal dimensional stability would be weakened. Results from thermogravimetric analysis (TGA) are in good accordance with the T_g values from DMA curves. Mechanical testing of the cured co-polymers shows that E51 can improve the mechanical properties of the co-polymers while its usage is controlled among 5% to 15%.     

碳酸二甲酯市场现状及技术进展

目前,全球碳酸二甲酯(DMC)的产量约为12万t/a。生产方法有光气法、酯交换法、甲醇氧化羰基法和二氧化碳-甲醇直接合成法。我国DMC产量不足3万t/a,主要采用酯交换法和甲醇液相氧化羰基法。DMC可作为羰基化试剂代替剧毒物质光气用于合成聚碳酸酯、异氰酸酯、杀虫剂西维因等,用作甲基化试剂代替致癌物硫酸二甲酯合成苯甲醚。     

MFE环氧乙烯基酯树脂固化性能的研究

本文对MFE环氧乙烯基酯(含MFE型和AFE型二种型号)树脂的固化性能(凝胶时间、放热峰和固化收缩率)作了报道并进行讨论。     

Self-emulsifiable soybean oil phosphate ester polyols for low-VOC corrosion resistant coatings

A series of soybean oil phosphate ester polyols (SOPEP) was prepared by reaction of fully epoxidized soybean oil with phosphoric acid and simultanoeous hydrolysis in the presence of a polar solvent. The polyols were characterized by determination of acid value, oxirane number, hydroxyl value, molecular weight (GPC), and FTIR spectra. These polyols with varying amounts of acid phosphate groups could be self-emulsified to form aqueous dispersions after neutralization with organic base. These aqueous dispersion showed varying degrees of stability and their appearance ranged from opaque dispersions to translucent to clear solutions. Waterborne coating compositions were prepared using these aqueous dispersions as principal components and their thermally cured film properties were studied. it was found that by careful selection and formulation, SOPEPs can be successfully used for low-VOC waterborne coating formulations. SOPEPs with 3.5% phosphate ester content showed visibly superior corrosion resistance properties.     

相转移催化合成蔗糖硬脂酸酯

采用相转移催化的基本原理和方法合成蔗糖硬脂酸酯,考察了反应时间、反应温度、原料的不同配比和催化剂用量对蔗糖硬脂酸酯产率的影响,得出反应时间为3 h,反应温度为95-100℃、硬脂酸甲酯与蔗糖的摩尔比为1:2.5,硬脂酸甲酯与PTC之比为1:0.07时为最佳配比。     

提高水玻璃砂强度的新方法

本文分析了酯法比ＣＯ２法硬化水玻砂强度高的原因，指出提高水玻璃粘结效率的关键是细化水玻璃凝胶粒。     

化纤油剂用表面活性剂单体的性能及应用

介绍了用作化纤油剂平滑剂、抗静电剂、乳化剂的磷酸酯、硫酸酯、脂肪酸酯、聚醚等表面活性剂单体的结构特点与性能 ,指出了应加速我国化纤油剂用表面活性剂单体的优化开发。     

吡啶为助剂合成甲酸甲酯的动力学研究

在60～90℃对以吡啶为助催化剂由一氧化碳合成甲酸甲酯的反应进行了动力学研究。结果表明该反应为2级反应,速率方程rυ=-dpco/dt=k[MOH]pco,无助催化剂时反应活化能Ea=67.63kJ/mol,反应速率常数k=9.66×106exp(-67.63×103/RT)(mol-1·L·min-1);当有助催化剂存在时,反应活化能为Ea=61.19kJ/mol,反应速率常数k=8.82×106exp(-61.19×103/RT)(mol-1·L·min-1)。并对助催化剂吡啶的助催化机理进行了探讨。     

Effects of hygrothermally decomposed polyurethane on the curing and mechanical properties of carbon black‐filled epoxidized natural rubber vulcanizates

Hygrothermally decomposed polyurethane (HD‐PUR) was mixed up to 20 phr in epoxidized natural rubber (with 50 mol % epoxidation; ENR50) recipes, and the curing and mechanical behaviors were studied. Mechanical testing of the ENR50/HD‐PUR vulcanizates determined the tensile, tear, compression‐set, hardness, abrasion, hysteresis, and resilience properties. No significant changes were observed in the tensile properties with the incorporation of HD‐PUR. The ENR50 compounds showed an increase in compression set with increasing HD‐PUR content. Rubbers cured by a semi‐efficient vulcanization system gave the best overall performance. A further improvement in curing and mechanical properties was achieved by the carbon black grade N330 being replaced with a more active grade (N375). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2265–2276, 2002