高强铝合金断裂韧性的研究现状及展望

通过对三种裂纹模式的概述，引出了铝合金断裂韧性的概念及断裂判据，重点评述了影响高强铝合金断裂韧性的内在与外在因素，以及断裂韧性与其它力学性能间的关系，最后提出了几个在今后的研究及应用中需要重点解决的问题。     

层状Ti3SiC2陶瓷的组织结构及力学性能

利用热压烧结TiH₂,Si和C粉获得了致密度大于98%的层状Ti₃SiC₂陶瓷。利用压痕法,在不同的载荷下测定了材料的维氏硬度, 发现其硬度值随载荷的增加而降低,在最大载荷30kg时,硬度值为4GPa。压痕对角线没有发现径向裂纹的出现。 这归因于多重能量吸收机制——颗粒的层裂、裂纹的扩展、颗粒的变形等。利用三点弯曲法和单边切口梁法测定了材料的强度和韧性分别为270MPa和6.8MPa·m1/2。Ti₃SiC₂材料的断口表现出明显的层状性质,大颗粒易于发生层裂和穿晶断裂,小颗粒易被拔出。当裂纹沿平行于Ti₃SiC₂基面的方向扩展造成颗粒的层裂,当裂纹沿垂直于基面的方向扩展时,裂纹穿过颗粒的同时,在颗粒内部发生偏转,使裂纹的扩展路径增加。裂纹的扩展路径类似人们根据仿生结构设计的层状复合材料。裂纹在颗粒内的多次偏转、裂纹钉扎以及颗粒的层裂和拔出等是材料韧性提高的主要原因。此外,在室温下得到的荷载-位移曲线,说明Ti₃SiC₂材料不象其它陶瓷材料的脆性断裂,而是具有金属一样的塑性。     

一种有机硫类絮凝剂DTC的合成及性能评价

讨论了由有机伯胺或仲胺和CS2合成二硫代氨基甲酸盐DTC的反应及副反应,简介了合成工艺。根据红外光谱确认了由三乙烯四胺合成的二硫代氨基甲酸盐（以下简称DTC）的结构。以含原油350 mg/L、含悬浮固体55.1 mg/L,含Fe^2＋10.0 mg/L的模拟污水为实验水样,考察了该DTC的絮凝性能,在40℃、pH=6-7、沉降时间30分钟条件下DTC的适宜加量为20 mg/L,此时污水含油量为9.0 mg/L;使用DTC的适宜pH范围在4-8,pH=6为最佳值,适宜温度范围为10-45℃,温度高于45℃时DTC可发生热分解;DTC的除油效果随污水中Fe^2＋浓度增大而改善。在含油89.1 mg/L、含悬浮固体55.1 mg/L、含Fe^2＋13.2 mg/L的油田污水中,DTC的除油率最高,远高于常用絮凝剂PFS,PAC,CPAM,HPAM和PAM。当污水中不含Fe^2＋时,DTC无絮凝除油效果。讨论了DTC在Fe^2＋参与下的絮凝过程。图5表1参8。     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

非均匀裂缝性油藏压力动态

在介绍具有连续基质颗粒大小分布和孔间表皮裂缝性油藏的不稳定压力分析模型的同时。提出了代表实际变化的裂缝密度和均匀性油藏的基质岩块大小分布概率密度函数，给出Laplace空间井筒压力解。该理论通过裂缝跨度变化拓宽了以前的双孔隙油藏模型，在不考虑孔间表皮的情况下，对非均匀裂缝性油藏压力动态进行了分析。     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

离心式高炉鼓风机扩压叶片断裂事故分析及处理

通过高炉鼓风机扩压叶片断裂事故，从化学分析、物理检验，结合使用情况对扩压叶片断裂原因进行了详细分析，并提出了改进措施。     

Microscale and mesoscale discrete models for dynamic fracture of structures built of brittle material

In this work we present the discrete models for dynamic fracture of structures built of brittle materials. The models construction is based on Voronoi cell representation of the heterogeneous structure, with the beam lattice network used to model the cohesive and compressive forces between the neighboring cells. Each lattice component is a geometrically exact shear deformable beam which can describe large rigid body motion and the most salient fracture mechanisms. The latter can be represented through the corresponding form of the beam constitutive equations, which are derived either at microscale with random distribution of material properties or at a mesoscale with average deterministic values. The proposed models are also placed within the framework of dynamics, where special attention is paid to constructing the lattice network mass matrix as well as the corresponding time-stepping schemes. Numerical simulations of compression and bending tests is given to illustrate the models performance.     

Correlation between quasi-static and dynamic crack resistance curves

The correlation between the crack resistance measured from dynamic and quasi-static J-R tests has been investigated based on test data from instrumented Charpy impact tests and quasi-static single edge notched bend (SENB) J-R tests.The method originally proposed by Aurich et al. [Analyse und Weiterentwicklung Bruchmechanischer versagenskonzepte--Lokales Risswachstum, Ermittlung des Risswiderstandsverhaltens aus der Kerbslagarbeit. BAM Forschungsbericht 192, Berlin 1993, ISBN 3-89429-329-2], to develop a correlation coefficient between the net fracture resistance of Charpy V-notch (ISO) and quasi-static compact tension tests, was extended to establish correlations between so-called ductile-brittle transition fracture resistance curves obtained from instrumented Charpy V-notched (ISO) and fatigue precracked impact tests and quasi-static SENB J-R fracture resistance tests.The correlation between the dynamic and quasi-static crack resistance with regard to practical application to fracture assessments appears to be reasonably consistent, bearing in mind the inherent scatter in crack resistance data in general. The findings of the present research project from testing of ship grade NVE 36 and pressure vessel steel to ASTM A516 Gr. 70 as well as two weldments in the NVE 36 steel, are in excellent agreement with the results of the research conducted by Aurich et al. [Analyse und Weiterentwicklung Bruchmechanischer versagenskonzepte--Lokales Risswachstum, Ermittlung des Risswiderstandsverhaltens aus der Kerbslagarbeit. BAM Forschungsbericht 192, Berlin 1993, ISBN 3-89429-329-2] for structural and pressure vessel steels to the German DIN standard steels including St 52-3, StE 355 and StE 460.     

硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景