烧结机双层插板式卸灰阀的研制

烧结机双层卸灰阀由蘑菇头式改为电液推杆插板式，有效地解决了系统卸料及漏风问题，实现了控制自动化，提高了设备作业率，改善了岗位环境。     

机械过冷的制冷系统在汽车空调中的应用

由于很多汽车空调采用斜盘式压缩机，有利于采用机械过冷的制冷系统，来增加汽车空调的制冷量、提高制冷效率。本文的主要目的是通过对系统工质的流量分配、空调制冷量和性能系数(COP)与中间压力之间的变化关系的研究，来研究机械过冷在汽车空调中应用的可行性。     

回转窑供电装置改造

本阐述了回转窑供电装置存在的缺陷，亦即改造过程和改造后的效果。     

空气压缩机无油润滑在山脚树矿的应用

山脚树矿有5台1966年上海生产的4L—20/8空气压缩机,运行很不经济,利用聚四氟乙烯合成材料制成活塞环,全部实现无油润滑运转,取得了良好的经济效益。     

"摩圣"技术在空气压缩机上的应用

介绍了4L-20/8型空气压缩机采用"摩圣"技术后的运行情况。"摩圣"技术在设备正常运行条件下能成功修复摩擦副的磨损,使之恢复原设计的尺寸和要求,因而提高了生产效率,取得了显著的经济效益。     

小型别墅中央空调的新风设计

提出了小型别墅中央空调新风处理的方法，就某别墅采用本方法作中央空调新风设计，并以其计算数据为依据，验证了本方法的可行性。     

码分多址（CDMA）技术和公用空中接口综述

本文主要讨论数字移动通信中扩频码分多址技术，阐明了ＣＤＭＡ体制的优越之外，分析了ＣＤＭＡ的关键技术，全面介绍了ＣＤＭＡ系统设计的基本原则和ＩＳ－９５－Ａ空中接口标准的含义。     

抽油机球铁齿轮的化学成分及生产工艺

为提高抽油机减速器齿轮铸件的机械性能，提出以Sn代替Mo作为合金元素，并通过试验确定了合理的Si、Cu、Sn的加入量。指出Si加入量应控制在1．9％－2．1％范围内，同时加入0．36％～0．9％的Cu和0．025％～0．07％的Sn，可保证球铁的强度和延伸率都满足QT700－2的要求。鉴于试件与实际铸件的表面硬度有一定的差值，为提高铸件表面硬度，进行了余热正火试验，并给出了铸件在铸型内的时间－冷却温度曲线。最后根据球铁化学成分的选择结果，进行了齿轮生产试验。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

条形药包药量计算公式探讨

本文通过现有诸药量计算公式的总结和统计分析，认为经验函数划（ｎ）以二次式较合适。并根据流体动力学理论和临界能量密度破碎准则，推导出ｆ（ｎ）的二次项公式，得ｑ＝ＫＷ２（１十ｎ２）／２；该式较符合实际，故推荐供参考。