石灰竖窑工作衬砖蚀损机理的探讨

阐述了石灰竖窑的预热带、煅烧带和冷却带工作衬砖蚀损机理，并讨论了如何根据耐火砖性能和石灰竖窑不同区域的蚀损机理，选择耐火材料。     

Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

基于切削振动相关性识别刀具磨损状态的模型与实验

本文提出基于切削振动相关性识别刀具磨损状态的研究思想,建立了车削中刀杆双向横振动系统及其单输入双输出系统的数学模型。理论和实验均表明,刀杆双向横振动之加速度响应在固有基频处的相干函数与刀具磨损状态之间有很好的规律性,它反映了两者之间的本质机理,并提供了识别刀具磨损状态的新途径。     

Morphological aspects of rubber fracture and wear

Morphology of carbon black (CB)‐filled rubber was studied with AFM and SEM and the classification of filler agglomerates, based on their internal structure and filler–matrix interactions, has been proposed. It varies according to the activity of CB and the kind of rubber. It has been shown that fracture of rubber starts either inside filler agglomerates (de‐cohesion) or in a filler–matrix interphase (de‐adhesion) initiating wear of the material. Microscopic observations correlate well with TGA and EPR data of wear debris collected during friction of rubber. The increase of thermal stability of CB and the appearance of additional spin signals, respectively, for elongated samples or debris, are proposed to be associated with de‐cohesion or de‐adhesion of the agglomerates. New approach to the fracture of rubber called “fatal agglomerate concept” is presented. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Al2O3—TiB2陶瓷刀具材料的高温氧化及其对刀具耐磨性能的影响

研究了Ａｌ２Ｏ３－ＴｉＢ２陶瓷刀具材料在１０００℃下的氧化行为，用ＸＲＤ、ＳＥＭ分析了氧化后的相组成及显微结构。结果表明：Ａｌ２Ｏ３－ＴｉＢ２陶瓷材料在１０００℃空气中氧化增重符合抛物线规律；随ＴｉＢ２含量的增加，该材料的抗氧化能力下降。     

Intelligent tool wear monitoring based on parallel residual and stacked bidirectional long short-term memory network

Effective tool wear monitoring (TWM) is essential for accurately assessing the degree of tool wear and for timely preventive maintenance. Existing data-driven monitoring methods mainly rely on complex feature engineering, which reduces the monitoring efficiency. This paper proposes a novel TWM model based on a parallel residual and stacked bidirectional long short-term memory (PRes–SBiLSTM) network. First, a parallel residual network (PResNet) is used to extract the multi-scale local features of sensor signals adaptively. Subsequently, a stacked bidirectional long short-term memory (SBiLSTM) network is used to obtain the time-series features related to the tool wear characteristics. Finally, the predicted tool wear value is outputted through a fully connected network. A smoothing correction method is applied to improve the prediction accuracy. The proposed model is experimentally verified to have a high prediction accuracy without sacrificing its generalization ability. A TWM system framework based on the PRes–SBiLSTM network is proposed, which has a certain reference value for TWM in actual industrial environments.     

High-speed milling of titanium alloys using binderless CBN tools

The performance of conventional tools is poor when used to machine titanium alloys. In this paper, a new tool material, which is binderless cubic boron nitride (BCBN), is used for high-speed milling of a widely used titanium alloy Ti–6Al–4V. The performance and the wear mechanism of the BCBN tool have been investigated when slot milling the titanium alloy in terms of cutting forces, tool life and wear mechanism. This type of tool manifests longer tool life at high cutting speeds. Observations based on the SEM and EDX suggest that adhesion of workpiece and attrition are the main wear mechanisms of the BCBN tool when used in high-speed milling of Ti–6Al–4V.