Butyltin Species and Inorganic Tin in Water and Sediment of the Detroit and St. Clair Rivers

Water and sediment samples from 29 locations in the Detroit and St. Clair rivers were analyzed for the highly toxic tri-n-butyltin (Bu₃Sn⁺) species and for the less toxic di-n-butyltin (Bu₂Sn²⁺) and n-butyltin (BuSn³⁺) species and inorganic tin. In general, locations sampled in the St. Clair River were less contaminated with butyltin species than those in the Detroit River. Inorganic tin and BuSn³⁺ were detected in over 90% of all subsurface water samples, while Bu₂Sn²⁺ and Bu₃Sn⁺ were detected in 45 and 28% of the same samples, respectively. The highest concentration ofBu₃Sn⁺ in subsurface water, 5.9 × 10^?10 mol Sn/L, was at the mouth of the Ecorse River, a tributary of the Detroit River. The three butyltin species and inorganic tin were also detected in 23–46% of all sediment samples. The highest concentrations of Bu₃Sn⁺ in sediment were found close to the mouths of the River Rouge, another tributary of the Detroit River, and the Ecorse River, and were 6.2 × I0^–7 and 1.7 × I0^–7 mol Sn/kg dry weight, respectively, for the top 2 cm of sediment.     

多掺炼新疆渣油的催化裂化工业生产技术

兰州石化公司以加工新疆原油为主，重油收率高，平均在37％左右，所生产的重油主要靠催化裂化装置来加工，多余部分以低附加值重油出厂。随着涩宁兰天然气工程的逐渐建成，低附加值重油出厂将受到严重威胁，因此，催化裂化装置加工重油显得尤为重要。兰州石化公司炼油厂1.2Mt/a重催装置通过采用先进技术进行改造，使重油掺炼比由41.52%提高到52.20%，提高了10.68个百分点，年多加工重油14.95万t，产品收率达到79.20%以上，能够灵活调节产品结构，创造了良好的经济效益。     

ICP-AES法测定封严涂层中BN含量

利用IC－AES法测定了封严涂层的BN，并对样品的溶解方法，仪器工作参数，光谱干扰等进行了研究。方法的相对标准偏差＜2％（n=10)，加标回收率在95％以上，方法简便，可靠，结果令人满意。     

西门子工业控制网络在棒材连轧生产线的应用

本文通过对包钢棒材连轧线的工业控制网络的由分体到整体的介绍,将西门子公司的三级控制网络(Profibus-DP网络、MPI网络、工业以太网)思想做了一个全面的说明.通过与现场实际相结合,使人们对这一概念有了更加清晰的认识.文章最后还结合作者的一些体会作了总结.     

Formation and investigation of epoxy intumescent compositions modified by active additives

Results are reported of research on intumescent composites based on epoxy resin cross‐linked with polyethylene polyamine and containing ammonium polyphosphate and such modifying additives as calcium borate, manganese dioxide, nickel, and chromium, containing tubulenes as gas‐formers and carbonization stimulators. The changes in composition and physicochemical properties of modified compositions under conditions of heat and fire were investigated by X‐ray photo‐electron spectroscopy, atomic force microscopy, and local force spectroscopy. Ammonium polyphosphate mainly stimulates carbonization processes on the inner surface of a bubble being formed during foam coke formation. The introduction of metal‐containing tubulenes leads to the formation of fire‐retardant and low flammability‐compositions with high coke and carbon structures content. The use of calcium borate in the compositions considerably increases the strength of foam coke being formed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1477–1483, 2002     

DDS—1型多功能电子实验箱

在进行各种电子实验、研制电子产品的过程中 ,信号源及各种测量仪表是必不可少的。DDS- 1型多功能电子实验箱即可满足这方面的需要。它自备 5路电源 ,能产生多种标准的模拟信号和数字信号 ;同时可方便地用来对各种信号的幅度、频率、工作状态等进行测量和显示 ;具有宽阔的实验操作平台、手提式机箱及组装式平面结构 ,使用、维护、携带均很方便。本文介绍该实验箱的功能、原理及设计特点。     

C5/C6异构化催化剂的首次工业应用

采用中石化金陵分公司研究院研制的CI-50(Pd/丝光沸石)作C5/C6烷烃异构化催化剂.详细介绍了该催化剂的工业放大试验装置的工艺流程、首次开工过程中技术问题及处理方法.     

Sol-gel processing: A versatile concept for special glasses and ceramics

The various parameters related to sol-gel processing are discussed with special reference to those which usually attract less attention but depending on the final product in mind, can play important roles. The versatility of the sol-gel technique in materials preparation is demonstrated by discussing the various products developed at the author’s laboratory by using this processing method.     

废塑料裂化生产汽柴油工业化装置研究

报道了废塑料炼油工艺中连续法、间歇法、半连续法等各种方法的特点 ;重点对各工业化流程中存在的问题和解决的方法进行了讨论 ,并提出了一些合理化的建议。     

A novel design in composities of various materials for solar selective coatings

This study describes the development of multilayer metal-dielectric graded index solar selective coatings in which the metallic volume fraction increases with depth, from top (air–film interface) to bottom (film–substrate interface). The work is based on computer simulation followed by validation through fabrication of the coatings and optical measurements. The influence of the choice of the number of layers present in a graded index composite selective absorber and results obtained for a new destructive interference bilayer (four-layer system) coating, designed using the computer model, were studied. The design and optimization of the composite coating was undertaken using a computer tool developed within this program of research employing Bruggeman and Maxwell–Garnett effective medium formalisms. The design tool enabled all key design parameters, with the exception of particle size and orientation, to be varied systematically to permit the sensitivity of the optical properties of the selective absorber coating to be studied.The model was validated with a supporting program of experimental research in which many different selective absorbers were prepared by co-sputtering of metal and dielectric materials.Although the best compositional gradation can be achieved by increasing the number of layers, the variation in optical performance beyond a certain number of layers is minimal. The destructive interference produced between adjacent layers contributes to the absorptance. The effect of the number of layers (single, four and 10) has been calculated for various materials such as nickel, vanadium, tungsten, cobalt and chromium based coatings. Solar absorptance of 0.98 and 0.96 was achieved by simulation and experimental findings with less than 0.07 thermal emittance at 300 K for 200 nm thick, 4-PGSAC (four-layer system) of V : Al₂O₃ composites. Other designs showed lower optical performance for all the material combinations regardless of their individual optical properties. Use of such thin film coating on the absorbers of solar thermal appliances can reduce thermal losses significantly, which could be of importance to the relevant industry.