对硝基苯偶氮2-羟基萘-3-甲酰烷基胺系聚丙烯纤维用红色染料的合成及应用

本文将2,3-酸在甲苯溶剂中用氯化亚砜酰氯化合成2-羟基萘-3-甲酰氯,将其分别和正丁胺、正辛胺、正十二胺和正十八胺反应制得4种不同碳链长度的2-羟基萘-3-甲酰烷基胺,用对硝基苯胺重氮盐与其偶合分别制得了对硝基苯偶氮2-羟基萘-3-甲酰正丁胺、对硝基苯偶氮2-羟基萘-3-甲酰正辛胺、对硝基苯偶氮2-羟基萘-3-甲酰正十二胺和对硝基苯偶氮2-羟基萘-3-甲酰正十八胺系聚丙烯纤维用红色染料。熔点分别为189.8℃、96.2℃、115.8℃和108.1℃;热分解点分别为273.1℃、216.0℃、258.0℃和221.0℃;最大吸收波长分别为515.8nm、516.8nm、513.6nm和514.2nm。在染色条件下,4支染料在聚丙烯纤维上的上染率分别37.6％、41.8％、42.4％和44.7％。     

高分辨率地震资料层位标定

高分辨率三维地震资料解释过程中层位标定是关键,标定过程中有误差,会相位源移,影响储层构造与构造解释的准确性。通过对泌阳凹陷赵凹地区高分辨三维地震资料层位标定的分析与研究,阐述了层位标定的方法,分析了标定效果,为构造断层解释及储层横向预测打下基础。     

Dynamics of hydrated iron(II) cations in nafion polymer membranes

Mössbauer studies of Fe²⁺ in water-soaked nafion polymer membranes in the temperature range between 90 K and 250 K have been performed. Above a critical temperature (～ 180 K) the spectra exhibit both elastic narrow absorption lines and quasielastic broad lines. These spectra are typical of bounded diffusion phenomena observed by Mössbauer spectroscopy in macromolecular systems like haemoglobin, myoglobin and ferritin. Similar spectral shapes have been observed by quasielastic neutron scattering from water in nafion membranes. Within 50 K above the critical temperature the total Mössbauer absorption area decreases by an order of magnitude whereas the narrow absorption line decreases by two orders of magnitude. The results are interpreted in terms of bounded diffusive motion of the iron. Using a model based on overdamped harmonically bound Brownian motion, the essential parameters of the iron motion can be derived as a function of temperature. The iron motion most probably reflects the motion of a large Fe²⁺ complex, e.g. Fe(H₂O)²⁺₆, which is attached to the polymer side chains via the sulphonic group.     

超高相对分子质量聚乙烯纤维研究进展

介绍了超高分子质量聚乙烯纤维的制备、表面改性及应用的研究进展 ,指出了今后超高分子质量聚乙烯纤维的研究及应用的发展方向     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

关于子母鱼雷的设想

概述了子母鱼雷这一新型鱼雷的设计基本依据的特点，论述了该鱼雷的作战使命与设计方案，叙述了发展子母鱼雷的必要性和可行性。     

镀液中SiC含量和粒径对Ni-P-SiC复合化学镀层性能的影响

采用化学镀方法制备了Ni P SiC复合镀层 ,系统研究了镀液中SiC含量和粒径对镀层结构及显微硬度的影响。结果表明 ,镀层中SiC析出量随镀液中SiC含量的增加而增加 ,在SiC含量一定的情况下 ,当SiC粒径为 7.0 μm时 ,析出量最大 ;镀液中SiC的含量和粒度对原始镀层的硬度影响不大 ,但对 4 0 0℃热处理后的镀层硬度有显著影响     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

紧凑型FLC光纤PDL模块

描述了紧凑型FLC（铁电液晶）光纤PDL（光子延迟线）模块的结构和运转特性；分析了插入损失；提出多信道运转时依赖于波长的设计方案。     

体积-表面淬火中加热温度的自动控制

根据表面-体积淬火奥氏体规范的要求，分析了感应加热过程中温度控制的特点和方式，并介绍了采用红外线光导纤维测温和微机控温技术成功用于体积-表面淬火中透热温度的自动控制。