Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation

The present study focuses on experimental investigation of through the thickness displacement and strain field in thin adhesive layer in single sided (unsymmetrical) patch repaired CFRP (carbon fiber reinforced polymer) panel under tensile load. Digital image correlation (DIC) technique is employed to acquire the displacement and strain (longitudinal, peel and shear) field. Experimental determination of shear transfer length based on shear strain field obtained from DIC is introduced to estimate the optimum overlap length which is an essential parameter in patch design for the repair of CFRP structures. Further, DIC experiment with magnified optics is performed to get an insight into complex and localized strain field over thin adhesive layer especially at critical zones leading to damage initiation. The failure mechanism, load displacement behavior, damage initiation and propagation are closely monitored using DIC. The influence of patch edge tapering on strain distribution in adhesive layer is also investigated. The DIC successfully captures the global and localized strain field at critical zones over thin adhesive layer and further helps in monitoring the damage based on strain anomalies. Strains are found to have maximum magnitude at the patch overlap edge and the shear strain level in adhesive layer is higher than the peel strain. Normal tapering increases the peel strain and has negligible influence on shear strain level in adhesive layer. The recommended overlap length is found to be consistent with the recommendation in the literature. Whole field strain pattern and the overlap length obtained from experiment are further compared with the finite element analysis results and they appear to be in good coherence.     

Simultaneous accommodation of Dy3+ at the lattice site of β-Ca3(PO4)2 and t-ZrO2 mixtures: Structural stability,mechanical, optical,and magnetic features

Structurally stable β-Ca₃(PO₄)₂/t-ZrO₂ composite mixtures with the aid of Dy³⁺ stabilizer were accomplished at 1500°C. The precursors comprising Ca²⁺, P⁵⁺, Zr⁴⁺, and Dy³⁺ have been varied to obtain five different combinations. The results revealed the fact that complete phase transformation of calcium-deficient apatite to β-Ca₃(PO₄)₂ occurred only at 1300°C, whereas the evidence of t-ZrO₂ crystallization is obvious at 900°C. The dual occupancy of Dy³⁺ at β-Ca₃(PO₄)₂ and t-ZrO₂ structures was evident; however, Dy³⁺ initially prefers to occupy β-Ca₃(PO₄)₂ lattice until its saturation limit and thereafter accommodates at the lattice site of ZrO₂. The typical absorption and emission behavior of Dy³⁺ were noticed in all the systems and, moreover, the surrounding symmetry of Dy³⁺ domains has been determined from the luminescence study. All the systems ensured paramagnetic response that is generally contributed by the presence of Dy³⁺. A gradual increment in the phase content of t-ZrO₂ in the composite mixtures ensured a significant improvement in the hardness and Young's modulus of the investigated compositions.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

光纤布拉格光栅的无源温度补偿

分析了通过施加应变补偿光纤布拉格光栅(FBG)中心波长随温度漂移的原理，给出了一种新型的无源温度补偿的方法和相应的实验结果。该方法采用了两种不同热膨胀系数的金属，对光栅先施加预应变。在0-60℃范围内，中心波长仅偏移了0．02nm。     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

复合材料的最新进展与应用

叙述了复合材料的发展概况 ,详细介绍了增强材料的种类、性能、形式及加工技术 ,指出了复合材料具有广阔的应用前景     

掺镱双包层高功率光纤激光器输出特性研究

对线形腔掺镱双包层高功率光纤激光器的输出特性进行了研究 ,通过求解速率方程 ,得到了激光器泵浦阈值功率、输出光功率和斜率效率的表达式。分析了光纤长度、腔镜反射率和泵浦波长等因素对激光器阈值功率、输出光功率和斜率效率的影响 ,为高功率光纤激光器的优化设计提供了理论依据     

DISPERSION COMPENSATION CFBG IN100km 10Gbit／s RECIRCULATING SYSTEMS

A 10Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.