管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

被动累积~(222)Rn-~(222)Rn探测器

本文采用 2只扩散杯 ,一只选择渗透率较大的滤膜 ,使2 2 2 Rn和2 2 0 Rn能很容易的进入。另一只选择渗透率较小的滤膜 ,该滤膜只允许2 2 2 Rn进入 ,半衰期较短的2 2 0 Rn被阻挡在外面。通过不同滤膜扩散率的差异 ,改变探测器的空气交换率 ,从而达到同时测量2 2 2 Rn和2 2 0 Rn的目的     

TEMIC射频卡的速率自适应读卡算法

提出种基于TEMIC射频卡Manchester编码的速率自适应读卡算法,并对该算法进行了说明和示例。     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

RLL码的计算机辅助设计

本文着重讨论计算机辅助设计RLL码的具体实现问题.该过程首先根据RLL码两个参数d,k确定一个编码率p/q,然后构造出RLL码的高阶状态转换-输出符号矩阵并求相应的近似特征向量.最后通过状态分裂和状态归并过程,即可得到一个满足d,k约束的编码输出表.其中状态转换-输出符号矩阵为实现计算机辅助设计RLL码提供了有效的数据结构,而且要优化RLL码编码器,就必须有选择地进行状态分裂.     

高峰值功率重频脉冲固体激光器

综述了高峰值功率重频脉冲固体激光器的发展现状，对其中的Ｑ开关、腔倒空、锁模等窄脉冲技术和放大技术进行了分析，展示了高峰值功率重频脉冲固体激光器的发展前景。     

45号钢二次枝晶臂间距与冷却速度的关系

本文利用可控平均冷却速度的单向凝固实验炉测定了４５号钢在不同平均冷却速度下的冷却曲线，由此得到其在凝固期间的平均冷却速度Ｒ，相应地测量了不同平均冷却速度下试样的二次枝晶臂间距Ｓ２，通过回归，得到了如下关系式：Ｓ２＝７２７Ｒ－０．４１，并将引式成功地应用于实际生产中。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Ni对球墨铸铁热处理的影响

采用电子探针，图象分析仪、差质变分析仪和Ｘ射线衍仪定量研究了Ｎｉ在球铁中的分布和Ｎｉ铸态球铁组成相比例奥氏体中含碳量以及贝氏体转变ＴＴＴ曲线线的影响，结果表明，Ｎｉ在球铁中呈连续负偏析，其加入可以影响球铁组成上比例，并使粤氏体中含碳量和贝氏体转变孕育期期增加。