Effects of Ti,Y, and Hf additions on the thermal properties of ZrB2

Reactive hot pressing was utilized to synthesize and densify four ZrB₂ ceramics with impurity contents low enough to avoid obscuring the effects of dopants on thermal properties. Nominally pure ZrB₂ had a thermal conductivity of 141 ± 3 W/m K at 25 °C. Additions of 3 at% of Ti, Y, or Hf decreased the thermal conductivity by 20 %, 30 %, and 40 %, respectively. The thermal conductivity of (Zr,Hf)B₂ was similar to ZrB₂ synthesized from commercial powders containing the natural abundance of Hf as an impurity. This is the first study to demonstrate that Ti and Y additions decrease the thermal conductivity of ZrB₂ ceramics and report intrinsic values for thermal conductivity and electrical resistivity of ZrB₂ containing transition metal additions. Previous studies were unable to detect these effects because the natural abundance of Hf present masked the effects of these additions.     

Strength and dilatancy behaviors of deep sands in Shanghai with a focus on grain size and shape effect

With rapid development of infrastructures like tunnels and open excavations in Shanghai, investigations on deeper soils have become critically important. Most of the existing laboratory works were focused on the clayey strata up to Layer 6 in Shanghai, i.e. at depth of up to 40 m. In this paper, Layers 7, 9, and 11, which were mostly formed of sandy soils at depth of up to 150 m, were experimentally investigated with respect to physico-mechanical behaviors. The stress–strain behaviors were analyzed by the consolidated drained/undrained (CD/CU) triaxial tests under monotonic loading. One-dimensional (1D) oedometer tests were performed to investigate the consolidation properties of the sandy soils. Specimens were prepared at three different relative densities for each layer. Also, the micro-images and particle size analyzers were used to analyze the shape and size of the sand grains. The influences of grain size, density, and angularity on the stress–strain behaviors and compressibility were also studied. Compared to the other layers, Layer 11 had the smallest mean grain size (D₅₀), highest compressibility, and lowest shear strength. In contrast, Layer 9 had the largest mean grain size, lowest compressibility, and highest shear strength. Layer 7 was of intermediate mean grain size, exhibiting more compressibility and less shear strength than that of Layer 9. Also, the critical state parameters and maximum dilatancy rate of different layers were discussed.     

Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.     

高精度多环片自动装配控制技术

为了实现对微小环片零件的自动化装配,搭建了自动装配系统.通过4根直线导向轴与4个直线轴承来提高系统的导向精度和刚度.采用直线导轨进行各装配作业模块之间的切换,保证了微小环片零件的自动装配与取出.在环片的装配方向上,螺旋升降机和光栅尺实现环片的位置精度控制.在Lab VIEW编程环境中,采用分层软件架构和模块化控制思想,避免了不必要的数据循环检测与丢失,能够达到环片组件的装配精度要求.控制系统分为系统初始化模块、参数设置模块、装配模块和取出模块,自动装配系统通过各个模块间的相互交流配合完成装配任务.采用本文中自动装配系统装配环片的实验结果表明,环片零件装配的最大位置误差为26μm,垂直度误差为17μm,平均装配时间为75 s/片,可满足环片组件所需的精度要求.     

一种军棋机器博弈的多棋子协同博弈方法

针对在军棋博弈不完全信息对弈中，面对棋子不同价值、不同位置、不同搭配所产生的不同棋力，传统的单子意图搜索算法，不能满足棋子之间的协同性与沟通性，同时也缺乏对敌方的引诱与欺骗等高级对抗能力。本文提出一种结合UCT搜索策略的高价值棋子博弈方法，实现高价值棋子协同博弈的策略。实战经验表明:高价值多棋子军棋协同博弈策略优于单棋子军棋博弈策略。     

High-Tg porous polyimide films with low dielectric constant derived from spiro-(adamantane-2,9′(2′,7′-diamino)-fluorene)

Porous polyimide (PI) films with low dielectric constants and excellent thermal properties have been a pressing demand for the next generation of high-performance, miniature, and ultrathin microelectronic devices. A series of novel porous PI films containing fluorenyl-adamantane groups were prepared successfully via thermolysis of poly(ethylene glycol) (PEG) added in the PI matrix. The cross-sectional morphologies of porous PI films showed closed pores with diameters ranging from 135 to 158 nm, which were uniform and regular in shape without interconnectivity. These porous PI films exhibited excellent thermal properties with a glass-transition temperature at 376 °C whereas the 5% weight loss temperature in air excess of 405 °C due to enhanced rigidity afforded by fluorenyl-adamantane groups. Accompanied by thermolysis content of PEG increasing from 0 to 20 wt %, the density of porous PI films decreased, and the corresponding porosity grew significantly from 0 to 11.48%. Depending on porosity, the dielectric constant and dielectric loss of porous PI films significantly declined from 2.89 to 2.37 and from 0.050 to 0.021, respectively. These excellent properties benefit the as-prepared porous PI films for application as interlayer dielectrics, integrated circuit chips, or multichip modules in microelectronic fields. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47313.     

高浓度聚合物驱提高采收率方法实验研究

为探索一种新的提高原油采收率的方法,在外形尺寸为4.5 cm×4.5 cm×30 cm、气测渗透率0.9~1.0μm2、变异系数为0.72的二维纵向非均质人造岩心上,模拟大庆油田油藏流体性质及温度条件,研究了高浓度聚合物(HPAM)驱注入时机、聚合物相对分子质量、聚合物段塞体积及段塞组合对驱油效果的影响。通过注入大分子量、高浓度聚合物,结合合理的注入方式,在化学剂成本与三元复合驱相当的情况下,采收率比水驱提高20个百分点以上,接近或超过三元复合驱的水平。实验表明,采用高浓度聚合物驱油是一种较好的提高原油采收率的方法。