Cure monitoring via different techniques: Isothermal cure of an epoxy-novolac molding compound

The isothermal cure of an epoxy-novolac molding compound was studied by means of Fourier-transform infrared spectroscopy (FTIR) and dielectrometry (DE). Results obtained were compared with previous differential scanning calorimetric (DSC) observations. The behavior of epoxide conversion (_FTIR) measured via FTIR was found similar to (but not exactly coinciding with) the extent of cure (_DSC) determined previously by means of DSC. As for the DE analysis, directly measurable properties such as permittivity () and loss factor () varied in a complicated manner during the course of cure, showing strong dependence on both temperature and frequency. Other dielectric parameters (such as ionic conductivity, relaxed permittivity, and characteristic relaxation time) previously suggested in the literature as suitable for cure monitoring purposes were found difficult to determine within the limited frequency range (10⁰ to 10⁴ Hz) here. With some arbitrariness, the relative drop in log (at 100 Hz) was taken as an index (_DE) for the extent of cure. It was observed that _DE behaves in a manner similar to _FTIR and _DSC Comments on the application of these three techniques in the characterization of thermosetting systems were given.     

Li4Ti5O12/Fe3O4复合材料的制备及其电化学性能

以醋酸锂和钛酸四正丁酯为原料,制备了纯相Li_4Ti_5O_(12),再用简单的水热法合成Li_4Ti_5O_(12)/Fe_3O_4复合材料作为锂离子电池的负极材料,通过XRD、SEM以及电池测试系统对纯相Li_4Ti_5O_(12)和Li_4Ti_5O_(12)/Fe_3O_4复合材料进行了结构、形貌及电化学性能测试。结果表明,制得的复合物具有较好的球形结构且粒径较小(200～300 nm),综合电化学性能较好。由于复合的Fe_3O_4有较高的理论容量,该Li_4Ti_5O_(12)/Fe_3O_4复合材料表现出比纯相Li_4Ti_5O_(12)大的容量,在1.0 C下循环100圈后,Li_4Ti_5O_(12)/Fe_3O_4的放电比容量仍能达到470.2 m A·h/g,同时也表现出比纯相Li_4Ti_5O_(12)更优的倍率性能。     

化学镀镍复合配位剂的研究

采用对比试验和正交试验,以镀速、孔隙率、镀液稳定性和镀层硬度为评价指标,研究了单一配位剂及复合配位剂对镀液和镀层性能的影响,得到了复合配位剂的最优组合:8.4g/L乳酸,6g/L苹果酸,9g/L柠檬酸,8g/L丁二酸,1g/L丙酸。采用该复合配位剂的工艺配方可提高镀液使用寿命,获得性能优良的镀层。     

Melting aspects of filled compounds in a modular co‐rotating twin screw extruder

In the polymer industry, precompounded materials are widely used. Carefully designed melting experiments were carried out to investigate melting mechanisms in master batched polymer compounds, using an intermeshing co‐rotating twin screw extruder. Calcium carbonate or aluminum powder was master batched with linear low‐density polyethylene (LLDPE). The calcium carbonates, which were used in the compounds, have differences in weight fraction and particle size. The compounds containing filler have higher thermal conductivities and viscosities than neat polyethylene. We observed melting initiation and propagation mechanisms of LLDPE compounds by removal and characterization of polymer compound carcasses in the melting region. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1990–2012, 2006     

复配菌对原油除蜡降黏效果分析

为提高含蜡原油流动性能,从辽河油田附近经受原油污染的土壤中筛选出两株原油降解菌。经过16S rRNA基因序列比对鉴定,菌株为纤维微菌属(Cellulosimicrobiumsp.)和假单孢菌(Pseudomonassp.),命名为7#和12#。将筛选出的7#菌与12#菌优化复配使用,研究结果表明:复配菌对液体石蜡有乳化效果,当复配菌体积比为1∶1时,乳化率最高达到77.5%;最适的生长温度为35～40℃,p H=6～8,最佳接种量(体积分数)为4%,复配菌体积比为1∶1,且培养基在初始pH,即pH=7时复配菌生长状态最佳。复配菌在37℃,pH=7条件下对原油处理7 d后,除蜡率为61.32%,降黏率达到31.58%;显微镜观察蜡晶变小,进一步说明菌株能够降解石蜡,破坏蜡晶结构,提高含蜡原油的流动性能。     

硫化物在纳米HZSM-5催化剂上催化转化性能及机理研究

研究了催化裂化（FCC）汽油中硫化物类型和含量，特别考察了各种硫化物在纳米HZSM-5催化剂上的催化转化性能，并探讨了硫化物的加氢脱硫转化机理。结果表明FCC汽油中硫化物主要为硫醇、噻吩、烷基取代噻吩和苯并噻吩等，其中，烷基取代噻吩占总硫化物的65％-73％。在纳米HZSM-5催化剂作用下，FCC汽油的硫化物都较易被脱除。烷基取代噻吩脱硫机理一方面含有直接加氢脱硫反应路线，另一方面含有裂解反应、烷基化反应和异构化反应路线。     

[火用]分析环境模型及其确立原则的研究

对现有的环境模型和有关环境模型的理论进行了评述和分析，指出了确定环境模型的理论以及现有的环境模型中存在的问题，提出了比较系统的确定环境模型的理论原则。     

尿基复混肥的生产应用

论述了我国发展高浓度复合型肥料的必要性，介绍了以尿素为氮源生产复合肥的特点，以团粒法、料浆法、熔体法和掺混法为代表，介绍了尿基复混肥的生产方法和工艺技术特征。     

有机-无机复混肥料的肥料效应初探

选取鸡粪为有机原料 ,进行发酵与不发酵两种前处理 ,设计 0、30 %、4 0 %、6 0 %和 10 0 % 5种有机氮水平 ,在水稻上连续两年试验。结果表明 ,在 4 0 %水平以下 ,作物产量随有机氮的增加而增加 ,超过 6 0 %产量下降 ,但有后效。氮素表观利用率与有机氮成正相关 ,当有机氮达到 10 0 %时 ,氮素利用率达到 5 3.4 %。随有机氮的增加 ,作物吸收养分向子粒中转移的比例也相应增加     

氨纶氯水降解及耐氯机理的探讨

应用红外光谱分析方法，对氨纶（ＰＵ纤维）氯水降解及耐氯机理进行了初步的研究。结果表明，ＰＵ浸氯水后，因受活性氯原子的攻击，ＰＵ大分子软链段的碳－碳键发生断裂，形成碳－氯化合物，添加剂加入后，因与ＰＵ大分子的软链段形成螯合物，从而避免了活性氯原子的攻击，有效地保护了软链段，使氨纶耐氯性能明显改善。