Surface stress effects on the thermodynamics of epitaxy

An analysis of the thermodynamics of epitaxy in thin films is presented which includes the effects of the surface stresses of the free surface and the film-substrate interface. It is shown that these effects, which are usually ignored in the theory of epitaxy, can have a major influence on both the critical thickness for epitaxy and on the partitioning of the misfit strain between the volume elastic strain and interface dislocations.     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。     

地应力及其测量法简介

地应力对工程岩体的稳定性影响很大，工程实践中常需定量地确定工程范围内的地应力。本文简要地介绍了地应力的概念、应用及常用的测量方法。     

A theoretical and photoelastic contact stress analysis relevant to orthopaedic knee prostheses

This study is based on a theoretical and photoelastic static contact stress analysis, relevant to the design of the plastic tibial plateau in an orthopaedic knee prosthesis. It involves the review of existing theoretical analyses concerned with the contact mechanics of layered elastic systems and, where possible, the validation of any relevant findings using two dimensional photoelasticity. Significant findings include the identification of a general minimum recommendable design thickness for the plastic tibial plateau, the endorsement of using the Hertzian contact theory to predict contact stress levels in the tibial plateau of certain knee implants and the slight improvement in contact conditions in the plastic when the plateau is perfectly bonded to its supporting metal tray.     

Residual Stress Evolution in Repair Welds

Abstract: The aim of this paper is to study the influence of the repair procedure on the evolution of residual stress distribution in butt welds. C-Mn steel coupon plates of 11 mm thickness were prepared, subjected to stress relief heat treatment and welded with two beads, using the gas metal arc welding process. After the deposition of two weld beads, two successive repair welds were made on the middle length of the second bead. Longitudinal and transverse residual stresses were measured in the vicinity of the weld, after deposition of the two weld beads and after each repair weld. Residual stress evaluation was conducted using an X-ray diffraction method. The repair welds caused a decrease in magnitude of the initial longitudinal residual welding stresses, and an increase of the transverse residual stress magnitude, in tension at points within the repair length, and in compression at points outside the repair length.     

转子叶片在非均匀来流条件下的流体激振特性

该文通过研究得出非均匀来流对转子叶片流体激振的三个重要特征 :非均匀来流相对于转子叶片的非定常流中主频分量是产生叶片动应力的决定因素 ;非均匀来流的非均匀度 (相当于非定常流的波幅 )大小和叶片流体激振的动应力大小成正比 ;转子叶片流体的定常压力水平与叶片动应力的水平密切相关。图 4表 2     

Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

封隔器胶筒接触应力分布有限元计算

利用ANSYS软件对3种封隔器胶筒的接触应力进行了有限元计算，得到了接触应力沿胶筒轴向的分布情况。比较不同结构封隔器胶筒在相同条件下的接触应力分布，可知新型封隔器胶筒在高压下接触应力分布更为均匀合理，具有较好的应用前景。