流动注射分光光度法测定钴

研究了将ＰＡＮ用于流动注射（ＦＩＡ）分光光度法测定微量钴，在５６０ｎｍ处绘制标准曲线，线性范围为０～４５μｇ／ｍｌ，相关系数０．９９６，方法的相对标准偏差（ＲＳＤ）小于３％，加标回收率为９５％～１０５％，进样频率８０次／ｈ。本法简单快速，用于面粉、分子筛，铝合金测定结果令人满意。     

美国UCC公司项目实施八段法

国外工程公司的项目实施工作法是科技发展和经济发展的产物。公司为谋求生存和发展,必须采取先进的技术和科学管理,同时获得适当的利润回报。本文介绍美国UCC公司的项目工作八段法。     

用迁移率和载流子浓度研究碲镉汞中的深能级

获得了一种研究碲镉汞深能级的方法。通过分析迁移率 载子浓度与温度的关系，可以得到关于深能级的重要依据。     

Daily impact of climate on the pattern of urban family life : Indigenous courtyard houses of Baghdad regions of the hot-dry climates Part I: Daily shifts or daily movements in summer

During the day, there are considerable variations in the climatic factors prevailing in these regions. This is especially so during the 24-hour daily cycle of the long, hot and dry summer (mid-May to midOctober). Such climatic conditions have had a considerable impact on the daily living pattern of family life in the same season, particularly in the urban areas. During the same 24-hour cycle, they have compelled the inhabitants to shift their living activities both vertically in section and horizontally in plan; they do this in pursuit of more acceptable, if not, desirable internal thermal environmental ambience.     

弹性杆与水下壳体接触冲击的冲击力计算研究

对弹性杆与水下壳体接触冲击问题进行了研究，用有限元法模拟壳体，边界无法模拟无限域流体，通过温面上的耦合条件进行联立求解，文中给出了典型算例，并进行了有关讨论。     

Energy Value of Resistant Starch

Resistant starch was evaluated for energy value using fine silica and normal starch as controls and young rats as a test model. The net increase in rats' carcass energy due to the test materials fed over a 3-wk period formed the basis for assessing energy value. Rats fed normal starch deposited about twice as much fat and significantly more protein in the carcass than those fed either resistant starch or silica. Rats fed resistant starch or silica showed similar growth responses and increases in components of body composition and carcass energy content. This suggested that resistant starch provided, like silica, no energy.     

Si_（1－x）Ge_x／Si定向耦合器的研制

在运用ＳｉＧｅ脊形波导单模条件和有效折射率法分析ＳｉＧｅ／Ｓｉ定向耦合器结构参数的基础上，采用分子束外延和各向异性腐蚀技术制备出Ｓｉ１－ｘＧｅｘ／Ｓｉ（ｘ＝０．０５）单模定向耦合器．在波长为１．３μｍ时，平均串音小于－１８．１ｄＢ，输出功率耦合效率达到９８．１％     

粉末涂层抗冲击缺陷分析

讨论了粉末静电涂装中出现的涂层抗冲击试验缺陷，通过设计实验寻找造成该缺陷的原因，揭示了产生涂层起皱和脱离基材的原因是钢板与磷化液之间的匹配性差。通过提高磷化液的游离酸酸度解决了该问题。从理论上推出了游离酸与附着力之间可能的关系：游离酸影响磷化膜与基材的结合力，或影响形成的磷化膜的形态。     

夏季面漆起泡的预防

面漆漆膜在夏季潮湿天气下成膜后3—5天，漆膜表面易形成米粒状的漆泡，针对漆泡的现象，寻找其形成的机理，根据起泡的机理采取预防面漆起泡的措施。     

Ti-6-22-22S合金步进轧制工艺加工棒材研究

采用步进轧制工艺制备了Ti-6-22-22S合金Ф50mm棒材，对加工、热处理、组织与性能的关系进行了分析。结果表明：在两相区上部温度960℃轧制获得细网篮组织，棒材性能较好且数据均匀；热处理后，得到双态组织，强度．塑性达到优良组合，而片层状组织强度较高，但塑性稍低。