注蒸汽开发稠油油藏采收率计算公式探讨

从辽河油区的地质条件和开发特征出发．立足单因素分析，在着重研究渗进率、净总厚度比和单层厚度对原油采收率影响的基础上。利用《价值工程》中的“功能重要评价法”，优化出不同类型稠油油藏蒸汽吞吐和蒸汽驱开发阶段的采收率计算公式．经实际资料验证，该公式对油田开发前期确定采收率丰和可采储量，具有较好的适用性。     

油田热采注汽管道在线检测技术现状

稠油热采注汽管道由于长期在高温、高压下运行,极易发生各种损伤,如腐蚀、裂纹、材料退化等,极易造成管道承压能力降低,发生失效事故。如何检测出潜在危险性缺陷,判断注汽管道能否继续使用,是保证注汽管道安全运行的关键问题。探讨了高温压力管道在线检测技术发展现状及其应用范围。     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橇装式模块化注聚合物站的设计

针对以往固定式注聚站建设和运行所存在的问题 ,成功设计了橇装式模块化注聚合物站 ,将注聚合物工艺所需的地面设备和装置均以橇装形式集中于 6～ 7个橇块 ,实现了注聚站的模块化、整体快速搬迁和现场快速连接施工 ,有利于设备运行、管理和阶段移动配注作业。对装置的基本流程和配置 ,以及基本参数的确定做了详细阐述。现场应用情况表明 ,该注聚站完全满足注聚合物工艺要求。与常规注聚站相比 ,不但造价降低 ,而且在减少现场作业量及设备再利用等方面有了明显的改善     

江苏复杂断块高含水单元改善水驱效果的技术对策

在分析高含水开发单元特点的基础上,针对该阶段剩余油的品位、分布和油水关系极为复杂、挖潜难度大的技术难点,提出了适合江苏复杂断块油田高含水开发单元改善水驱开发效果的思路和工作程序、技术对策,并在真武油田高含水开发单元进行了实际应用,取得了良好的效果.     

单家寺油田单6东超稠油开采配套工艺技术

在单家寺油田单6东超稠油油藏地质特征和渗流特点研究的基础上，成功研制了亚临界湿蒸汽发生器。通过超稠油油层保护、化学物理方法辅助蒸汽吞吐、高饱和预充填复合防砂、注汽—采油—井筒电加热一体化举升、动态监测和地面集输六项配套工艺的研究及应用，实现了开采超稠油油藏的技术突破。     

注入种子CuBr激光器中的光谱控制

报道了采用注入种子方法．对ＣｕＢｒ激光器进行激光模式控制的实验结果。实现了单纵模ＣｕＢｒ激光脉冲的注入放大，获得了功率为１００ｍＷ水平的窄线宽铜激光辐射．在理论上分析了短脉冲高增益激光器中注入种子过程，讨论了在注入种子ＣｕＢｒ激光器中进行光谱控制的实验结果．     

临盘油田分层注水管柱有效率影响因素分析

分层注水管柱有效率低一直是困扰临盘油田开发生产的一大难题。针对这一现状，在分析油藏结构、施工工艺和现场资料的基础上，分析了影响分层注水井管柱有效率的因素，阐述了封隔器、工艺操作、管枉自身及温度等制约分层注水管柱有效率提高的原因，并提出了相应的对策和措施。     

Advances in titanium metal injection molding

The approaches to production of titanium powder injection molded parts are reviewed. Historically, oxygen levels have been too high for structural use (particularly with the Ti-6Al-4V alloy). However, recent advances in starting powders, binders and sintering facilities now allow oxygen levels in the Ti-6Al-4V alloy to be controlled to about 0.2 wt.% oxygen. This should result in significant expansion of the titanium PIM market place into aerospace, automobiles, surgical instruments, dentistry, communication devices (such as computers and cell phones), knives and guns. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 5–6 (455), pp. 118–125, 2007.     

Simulation of Natural Depletion and Miscible Gas Injection Effects on Asphaltene Stability in Petroleum Reservoir Fluids

Natural depletion of petroleum reservoirs as well as gas injection for enhance oil recovery, are unavoidable processes in the oil industry. Foremost, prediction of the problems due to these two processes is very necessary and important. So many field and experimental experiences have shown that heavy organic depositions, especially asphaltene deposition, are principal results during these processes. Results of laboratory simulation of asphaltene deposition during the natural depletion of petroleum reservoirs and also during gas injection and enhanced oil recovery (EOR) processes are reported here. This is achieved through the design of a new experimental setup for the investigation of pressure and composition effects on asphaltene deposition in petroleum fluids at high pressure and high temperature conditions. In this work, asphaltene deposition during decreasing pressure, from pressures greater than reservoir pressure to pressures below the bubble point pressure (natural depletion) and also asphaltene deposition during natural gas injection in reservoir conditions, are studied for three samples—one recombined sample and two bottomhole samples. All of the obtained results from this work conform to theoretical and other experimental works.