离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

红外光谱法用于快速测定车用柴油酸度等性质的研究

针对车用柴油酸度等性质测定过程繁琐，采用衰减全反射样品池测定车用柴油的红外光谱，用偏最小二乘法（PLS）建立红外光谱测定车用柴油酸度、密度、闪点和凝点的4个校正模型，验证标准误差分别为0.46 mg/(100 mL),0.77kg/m3,2.60 ℃,2.77 ℃，该方法符合标准方法再现性要求。与标准方法相比，该方法具有无需预处理、操作简单、测量快速、重复性好等优点。     

XMAC纵波时差高分辨率处理方法

在充分调研阵列声波测井分波提取方法的基础上，针对阿特拉斯公司的交叉多极子阵列声波测井（XMACⅡ）提供的单极波形信息，研究纵波时差提取及高分辨率处理方法。首先利用相关-互功谱法高精度地提取纵波时差，然后针对XMACⅡ仪器的接收阵列，研究组合子阵列的方法，形成共发射子阵列和共接收子阵列，最后利用子阵列对提取的纵波时差做高分辨率处理。处理现场实际测井资料，并将高分辨率处理成果与引进的eXpress软件处理成果、实测的国产高分辨率声波（纵波）测井曲线及岩心纵波时差对比分析，表明该方法提取的纵波时差曲线的纵向分辨率有很大提高，时差计算准确可靠，提取的单极纵波时差与国产高分辨率声波时差及岩心纵波时差的平均相对误差均小于7%。该方法具有较高的实用价值和广阔的应用前景。     

Fast Positive Feedback Between the Adrenocortical Stress Response and a Brain Mechanism Involved in Aggressive Behavior.

Aggressive behavior induces an adrenocortical stress response, and sudden stressors often precipitate violent behavior. Experiments in rats revealed a fast, mutual, positive feedback between the adrenocortical stress response and a brain mechanism controlling aggression. Stimulation of the aggressive area in the hypothalamus rapidly activated the adrenocortical response, even in the absence of an opponent and fighting. Hypothalamic aggression, in turn, was rapidly facilitated by a corticosterone injection in rats in which the natural adrenocortical stress response was prevented by adrenalectomy. The rapidity of both effects points to a fast, mutual, positive feedback of the controlling mechanisms within the time frame of a single conflict. Such a mutual facilitation may contribute to the precipitation and escalation of violent behavior under stressful conditions. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

腐蚀阴极尖端的新方法

给出一种腐蚀阴极尖端的新方法,使得对阴极常用金属材料(W,Mo,Ir,Ta等)制作的阴极尖端的腐蚀效果明显,针尖对称性和重复性都很好,成品率和质量都有所提高.     

新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003