Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.     

Gamma ray irradiation induced point defects in BaF2

There are some original nonmagnetic point defects in the BaF2 crystallite powder,such as interstitial and vacant F^- which can become paramagnetic centers by γ-ray-irradiation at room temperature,Afterγ-ray irradiation the paramagnetic point defects Vk,H,F and M centers,have been observed in the sample with experiment of electron spin resonance(ESR).Frenkel exciton,a nonmagnetic point defect,can also be induced by the γ-ray irradiation in the sample at room temperature,the existence of the Frenkel exciton is affirmed by an anomalous change of the ESR signal of Vk center with temperature,The signals of the ESR of the H,F and M centers weaken and vanish with the temperature increasing monotonously,But the ESR signal of the Vk enhances when the temperature goes up about 127℃,then weakens and vanishes.An increase in the Vk center follows an annihilation of the Frenkel exciton with heating.     

BEM 系列原油流动性改进剂的应用

对BEM系列原油流动性改进剂的基本原理以及在中洛、濮临、东临、东黄、鲁宁、魏荆等几条原油长输管道工业应用的现场测试情况进行了介绍。结果表明，BEM系列原油流动性改进剂在降低原油凝点和粘度方面性能良好，能满足管道安全，平稳运行的要求。     

粉喷桩处理软弱地基在祁临高速公路的应用

结合工程实例，介绍了粉喷桩的所属类型，粉喷桩对软弱地基加固的原因，所适应土质及加固特点，阐述了祁临十八合同段的粉喷桩施工过程及施工中应注意的若干问题，得出粉喷桩处理不良地基效果良好。     

顶封封隔管柱的研制与应用

中原油田近年来注水压力不断升高，井况恶化严重，为此开发了顶封封隔管柱，主要阐述了管柱工况受力特点、结构、工作原理及现场使用效果。经现场较大面积的应用证明，各项性能、技术指标达到了现场要求。     

一种有效的优化的多载波通信系统的功率分配算法

本文提出一种关于DMT系统传输纯数据流业务的最佳的功率分配算法，该算法使用了一种有效的表格查手工艺工和拉格朗日乘法器对分搜索办法，能够较快的收敛到最佳的功率点。同时，易于用硬件和软件实现。     

双河油田特高含水后期开发阶段注采结构调整的实践与应用

针对双河油田的注采结构的现状及特征,通过近几年来在注采结构调整方面的实践与应用,总结出了油田在特高含水后期开发阶段,实现油田控水稳油目标的途径和方法,注水结构调整主要是结合地质特点,减少欠注层段,减少和控制不合理超注井层段和改善吸水剖面;在采液结构调整上,控制高含水层段的注入,加强中低渗透层段的注入,封堵高渗透、高水淹干扰层段,解放动用较差的中低渗透层段,改善平面上采出不平衡的状况。通过实施注采结构调整,双河油田在特高含水后期实现了高效开发。     

三维施工中SN388炮点表的设置

本文提供了SN388在三维施工中炮点表的几种设置方法，并进行了相应的对比说明，最后给出了改进炮点表设置的有关设想。     

Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.