T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

Preparation and characterization of polyurethane microcapsules containing n‐octadecane with styrene‐maleic anhydride as a surfactant by interfacial polycondensation

A series of polyurethane microcapsules containing a phase change material (PCM) of n‐octadecane was successfully synthesized by an interfacial polymerization in aqueous styrene‐maleic anhydride (SMA) dispersion with diethylene triamine (DETA) as a chain extender reacting with toluene‐2,4‐diisocyanate (TDI). The average diameter of microPCMs is in the range of 5–10 μm under the stirring speed of 3000–4000 rpm. Optical and SEM morphologies of microPCMs had ensured that the shell was regularly fabricated with the influence of SMA. FTIR results confirmed that the shell material was polyurethane and the SMA chains associated on core material reacted with TDI forming a part of shell material. The shell thickness was decreasing in the range of 0.31–0.55 μm with the molar ratio of DETA/TDI from 0.84 to 1.35 and the weight of core material increasing from 40 to 80% (wt %). By controlling the weight ratio of PCM as 40, 50, 60, 70, and 80% in microPCMs, it was found using DSC that the T_m and T_c of microPCMs were in the range of 29.8–31.0^oC and 21.1–22.0°C and an obvious phase change had been achieved nearly the same temperature range of that of PCM. The results from release curves of microPCM samples prepared by 1.4, 1.7, and 2.0 g of SMA indicated the release properties were affected by the amount of the dispersant, which attributed to the emulsion effect and shell polymerization structure. The above results suggest that the shell structure of microPCMs can be controlled and the properties of microPCMs determined by shell will perform proper practical usage. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4996–5006, 2006     

Control of structure and tack properties of acrylic pressure‐sensitive adhesives designed by a polymerization process

Free radical emulsion polymerization of methyl methacrylate (MMA) and 2‐ethylhexyl acrylate (EHA) results in the synthesis of pressure‐sensitive adhesives (PSAs) with good tack properties. Management of both the copolymer composition and the polymerization process allows one to control the behavior of the PSA. Semicontinuous (SC) processes create polymer particles whose instantaneous composition is close to that of the feed particle The SC Mixture process (continuous feeding with comonomer blends) affords nearly homogeneous latex particles and PSA films. The SC Gradient process (separate feedings at inversely varying rates) affords heterogeneous particles and films. The Batch process leads to somewhat heterogeneous films, but the hard (MMA‐rich) microdomains are made compatible with their soft (EHA‐rich) matrix because of the assumed formation of tapered‐type copolymers. Tack measurements indicate the importance of the particle and film structures. Too much hardness or softness leads to unacceptable lacks of adhesion and cohesion, respectively. Homogeneous structures prove adequate, but their tack properties collapse with rising temperature. Heterogeneous structures, with extensive phase segregation, prove unsatisfactory because they lack adhesion and cohesion. Finally, the association of well‐balanced composition and compatible heterogeneity is the criterion for suitable PSA behavior. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2749–2756, 2003     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

Short fibre elastomer composites: effect of fibre length,orientation, loading and bonding agent

A series of short fibre reinforced styrene butadiene rubber (SBR) composites were prepared by incorporating sisal fibres of different lengths and different concentrations. The vulcanization behaviour and the properties of the vulcanizates were measured by the relevant ASTM procedures. The processing characteristics such as green strength and mill shrinkage were improved by the addition of fibres. The properties like tensile strength, tear strength, moduli at 10% and 20% elongations were found to be maximum for composites containing longitudinally oriented fibres of length 6 mm. Mixes containing 35 phr loading of fibres and bonding agent showed better mechanical performance than others. The failure behaviour of tensile and tear specimens have been analysed by scanning electron microscopy techniques. Paper presented at the poster session of MRSI AGM VI, Kharagpur, 1995     

聚丙烯表面改性及与涂料的粘结

讨论了聚丙烯制品喷涂着色的优点及影响聚丙烯制品与涂料之间粘结强度的各种因素。综述和评价了对聚丙烯进行表面改性的必要性及各种表面改性方法。     

微加速度计粘附问题的研究及应用

粘附是影响微机电系统(MEMS)可靠性的重要因素之一。针对MEMS的典型产品——微加速度计的粘附问题进行了研究,给出了2种典型的微加速度计的表征粘附特性的剥离数的表达式,并分析了将粘附条件应用于微加速度计的多学科设计优化之中,分析了其对系统结构设计产生的影响。     

Morphology of intermetallic compounds formed between lead-free Sn-Zn based solders and Cu substrates

The morphologies of intermetallic compounds formed between Sn-Zn based solders and Cu substrates were investigated in this study. The investigated solders were Sn-9Zn, Sn-8.55Zn-0.45Al, and Sn-8.55Zn-0.45Al-0.5Ag. The experimental results indicated that the Sn-9Zn solder formed Cu₅Zn₈ and CuZn₅ compounds on the Cu substrate, while the Al-containing solders formed the Al_4.2Cu_3.2Zn_0.7 compound. The addition of Ag to the Sn-8.55Zn-0.45Al solder resulted in the formation of the AgZn₃ compound at the interface between the Al_4.2Cu_3.2Zn_0.7 compound and the solder. Furthermore, it was found that the cooling rate of the specimen after soldering had an effect on the quantity of AgZn₃ compound formed at the interface. The AgZn₃ compound formed with an air-cooling condition exhibited a rougher surface and larger size than with a water-quenched condition. It was believed that the formation of the AgZn₃ compound at the interface occurs through heterogenous nucleation during solidification.     

Interfacial polycondensation of diphenolic acid and isophthaloyl chloride

Interfacial polycondensation of diphenolic acid (DPA) and isophthaloyl chloride (IPC) in various solvent/water systems was investigated with tetrabutyl ammonium chloride as a phase transfer catalyst. It was found that a large mass of capsules were formed at the beginning of the reaction for all solvents examined but the capsule morphology and reaction results depended on the solvents. It is believed that the capsule shells make up of the reaction zone and a mechanism of the interfacial polycondensation is proposed accordingly. The effect of the solvents on the reaction was interpreted from the interaction between the polymer and the solvent according to the mechanism. The reaction conditions were optimized, and poly(DPA-IPC) with high intrinsic viscosity was prepared in high yield under the optimal condition. It is an amorphous polymer with glass transition temperature of about 160°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008