The Oxidation of NdFeB Magnets

The oxidation kinetics in air of a commercial NdFeB magnet have been investigated over the temperature range 335–500°C. The oxide microstructure has been characterized by SEM, XRD and cross-sectional TEM. The results show that the external scale formed consists of an outer layer of Fe₂O₃ and an inner layer of Fe₃O₄ but that the principal degradation process is the formation of an extensive zone of internal oxidation. HREM has been used to show that this zone contains NdO particles embedded in an -Fe matrix. These particles are discrete and very small, approximately 2 nm in diameter, and have an amorphous structure. The -Fe matrix has a columnar grain structure with a grain width of approximately 100 nm. It is argued that the high rates of internal oxidation arise because the external-oxide layers are not protective at the oxidation temperature, and oxygen penetrates to the zone front by fast diffusion along the columnar -Fe grain boundaries.     

芯棒位置对冷拔内螺旋凸筋管成型的影响

本文借助于有限元分析软件Marc对冷拔内螺旋凸筋管进行了有限元模拟,分析了芯棒与凹模的轴向相对位置对冷拔内螺旋凸筋管成型的影响.     

TEM studies of cross sections of oxidized Fe-25Cr-6Al-La alloy

The oxidation behavior of the alloy Fe–25%Cr–6%Al-RE (rich in lanthanum) was investigated by means of TEM analysis. The results show that after 2 hr oxidation of the alloy, in pure oxygen at 1200° C, La precipitated in the oxide scale at the top of -Al₂O₃ grains and at the grain-boundary regions in the form of tiny particles of hexagonal La₂O₃. These tiny particles prevented aluminum from diffusing toward the surface and suppressed lateral growth of the oxide scale. The rare-earth constituents accelerated the internal oxidation of the alloy during thermal cycling between 1200° C and room temperature. They appeared as particles of aluminum oxide and lanthanum oxide. Particles of cubic La₂O₃ precipitated in the alloy matrix near the oxide scale-metal interface in a direction parallel to grain boundaries.     

内氧化法制备Al2O3／Cu复合材料的再结晶行为

以Cu2O为氧化剂，采用Cu-Al合金粉末内氧化及后续的粉末冶金法制备了Al2O3／Cu复合材料。并将不同Al2O3含量的试样进行不同变形量的冷拔处理，在氮气保护下进行高温退火处理(700℃～1050℃，1h)。研究了硬度随退火温度的变化规律，观察了显微组织。结果表明：在铜基体中弥散分布着纳米级的Al2O3颗粒：经900℃，1h退火后Al2O3／Cu复合材料的硬度可保持室温的87％以上；其再结晶温度高达1000℃；变形量和Al2O3含量增加均使硬度提高，但对软化和再结晶温度影响不大。     

Ti和V对Fe中氢与位错交互作用的影响

研究了Fe-0.5wt-%Ti和Fe-0.5wt-%V合金中由氢与位错交互作用所形成的氢致冷加工内耗峰(H-CWP)。实验结果表明:合金元素对H-CWP、对氢与位错之间的交互作用有显著的影响,与氢作用愈强的元素,对H-CWP的影响愈大,内耗实验结果与力学性能之间存在着一定的联系.     

均匀设计法、神经网络和遗传算法结合在内高压成形工艺参数优化中的应用

内高压成形技术是以轻量化和一体化为特征的一种空心变截面轻体构件的先进制造技术。目前,内高压成形技术越来越受到人们的关注,特别是汽车制造企业。管材的内高压成形过程与很多因素有关,其中施加在管件内部的压力与轴向进给量之间的配比关系尤为重要,对两者的匹配关系进行优化是内高压成形面临的重要课题。传统的优化方法需要大量的模拟计算,耗时多且不易掌握。针对这一问题,该文提出了将均匀设计法、神经网络和遗传算法相结合进行参数优化,既利用了均匀设计试验的均匀可靠性,又运用神经网络的非线性映射、网络推理和预测功能,最后发挥遗传算法的全局优化特性,得出了最优结果,并直接为实际生产提供了可靠的参数依据。     

变形Fe-Nb-C合金的室温至180℃内耗

测量了700℃，30min水冷后变形Fe－Nb-C合金室温至180℃的内耗，发现除Snoek峰外，合金在此温度区还有阻尼峰。测量了合金经过980℃，2h中间处理样品的内耗，并给出变形及室温原位时效的汽车钢ST14与GBPH340的内耗结果。认为Fe-Nb-C合金的变形“B”峰。是被饱和Cotterll气团碳原子团簇钉扎的位错段拖曳碳的稀Cottrell气团运动引起的，是合金在变形时碳原子稀Cottrell气团择优分布在位错上的结果。     

EFFECT OF La ON SNOEK-KE-K■STER PEAK IN Fe-P-N ALLOY

研究了F? P—N合金加?对Snoek—Ke-Koster(SKK)峰的影响,发现与合金含La,P的原子浓度比(C_(La)/C_p)有关:对于C_(La)/C_p较大(例如4.56和2.6)的合金,La有明显增强SKK阻?效应:对于C_(La)/C_p=0.27的P过饱和合金,La对SKK峰无明显影响。     

Dynamic Young’s modulus and internal friction in polycrystalline copper

An attempt has been made to measure the temperature dependence of dynamic Young’s modulus together with the related variation of internal friction in polycrystalline copper. A mechanical spectroscopy study was employed using a standard servo hydraulic fatigue testing machine equipped with a scanning laser extensometer. Dynamic Young’s modulus and internal friction were measured over a temperature range of 298 to 873 K at very low frequencies of 0.1, 0.05, and 0.01 Hz. One internal friction peak was observed over the ranges 450 to 700 K, together with marked decreases in the dynamic Young’s modulus in the same temperature range. From a quantitative analysis of the experimental data with the relaxation strength, relaxation time, and activation energy, it is concluded that the peak phenomenon is due to grain-boundary sliding relaxation.     

Enhanced Oxygen Diffusion Along Internal Oxide–Metal Matrix Interfaces in Ni–Al Alloys During Internal Oxidation

A study of the internal oxidation of dilute Ni–Al alloys in an NiO/Ni Rhines pack was performed at 800, 1000, and 1100°C. Considerable deviations from the classical internal oxidation model have been observed. The rate of internal oxidation depends not only on the concentration of the alloying element but also on its nature, which contributes to determining the size, shape, orientation and distribution of the internal oxide precipitates. For instance, the precipitates in the Ni–Al alloys are continuous rods, arranged in a cone-shaped configuration that extends from the surface to the internal oxide front. The observed depths of internal oxidation for the various concentrations of aluminum are discussed and related to the morphologies of the internal oxide precipitates. The apparent N^(s) _oD_o values determined from internal oxide penetrations increase with increasing solute content in the alloy. It is postulated that diffusivity of oxygen is enhanced along the internal oxide–metal matrix interface compared with that in the metal matrix.