Synthesis and properties of peroxy derivatives of epoxy resins based on Bisphenol A: Effects of the presence of boron trifluoride ethereate

Oligomers containing peroxy groups have been synthesized on the basis of epoxides reacting with tert–butylhydroperoxide in the presence of boron trifluoride etherate. Dependence of reaction rates upon the quantity of catalyst, temperature and also nature of hydroperoxide has been investigated: A kinetic equation for the process has been formulated and also a kinetic scheme for the reaction taking into account the presence of boron trifluoride etherate is proposed. Structures of the synthesized peroxy oligomers have been confirmed by IR- and NMR-spectroscopy. The reaction initiating properties of the oligomers so synthesized were studied using as the example the styrene polymerization reaction. Electronic Publication     

8Li次级束的产生

在北京串列加速器次级束流线上通过2 H(7Li,8Li) 1H逆运动学反应产生了用于核天体物理研究的8Li次级束。准直后的次级束纯度达到 80 %以上 ,对于 44MeV的7Li强度约为 3 0s- 1·pnA- 1,可以用来进行逆几何转移反应的实验测量。     

多输入单输出逆高斯分布流域汇流模型

本文将逆高斯分布应用于由水库和区间组成的复杂的流域汇流系统，并建立了多输入单输出逆高斯单位线模型。讨论了模型参数的估计方法，并对沾益流域的雨洪资料进行了实例分析。     

PEG20000中试放大的工艺研究

在一定温度和催化剂作用下 ,分别利用本体聚合和溶剂聚合的方法 ,在 1L、10 0L不锈钢高压反应釜中合成了相对分子质量为 2 0 0 0 0的聚乙二醇 ,并讨论了聚合反应机理 ,研究了催化剂用量、反应温度、反应时间对聚合反应的影响。经过红外、核磁共振、凝胶色谱、化学分析等方法对产物进行了表征。     

烯烃聚合单活性中心非茂催化剂的最新研究进展

综述了近几年来烯烃聚合用单活性中心非茂催化剂的研究进展。简要介绍了 2 3种由前、后过渡金属组成的配位化合物催化剂的结构与性能     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

The solution of the inverse problem of gravitational potential using a set of measurements of different field elements

A numerical solution of the inverse problem of the gravitational field at a single point is obtained using six field elements for a point, a spherical cap, a differential spherical sector and a vertical segment. In the system of six equations obtained, the unknowns are the mass of the body, the depth of its center, and the second, third, and fourth degree moments. The accuracy of the solution of this system is ten times higher than when using three field elements. __________ Translated from Izmeritel’naya Tekhnika, No. 5, pp. 3–8, May, 2007.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.