石灰竖窑工作衬砖蚀损机理的探讨

阐述了石灰竖窑的预热带、煅烧带和冷却带工作衬砖蚀损机理，并讨论了如何根据耐火砖性能和石灰竖窑不同区域的蚀损机理，选择耐火材料。     

Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

正交曲线坐标下三维代数应力通量模型

针对弯曲及不规则明渠的水动力及物质输运特性，本文建立了曲线坐标系下的三维代数应力通量数学模型，对平面上弯曲及不规则复杂边界情形，采用Poisson方程进行正交曲线坐标变换，各向异性的湍流代数应力通量模型被引用于本文的模拟计算中，以体现复杂边界条件引起的水动力及物质输运特性的变化。通过180度强弯曲明渠水槽及贵溪电厂不规则边界河段物理模型试验两个实例计算表明，实测值与计算吻合良好，效果令人满意。     

球磨机衬板材料及热处理工艺

对传统的中碳低合金耐磨铸钢的化学成分和热处理工艺进行了优化设计 ,使新材料具有较高的强度、硬度和韧性 ,因而抗冲击、抗疲劳、抗磨损性能良好。实际应用表明 ,用此种材料代替油淬和风冷中碳低合金耐磨铸钢 ,不仅生产成本低 ,而且在矿山、电力球磨机制粉等工矿条件下 ,其使用寿命长     

Effects of fluoropolymer addition to an epoxy on scratch depth and recovery

Samples were prepared by addition of a fluorinated poly(aryl ether ketone) (12F-PEK) to a commercial epoxy resin and curing at either 24 °C or 70 °C. The concentrations of fluoropolymer in the samples were 0, 5, 10, 20, 30, 40, and 50%. Phase inversion facilitates the formation of more and more smooth surfaces for scratch testing with increasing fluoropolymer concentration. A progressively increasing load from 0.03 N to 12 N was administered with a diamond tip to the surfaces of the samples; depths were determined within ±7.5 nm. The original scratch depth is a function of the fluoropolymer concentration. Scratch recovery (healing) reaches values up to 95%. Plots of the residual depth versus concentration of the fluoropolymer at 4, 6, 8, and 10 N reveal minima for all forces and both temperatures. Addition of only 5% or 10% 12F-PEK improves the scratch recovery significantly. The results are explained by changes of material morphology with the fluoropolymer concentration. Electronic Publication     

数值地形图的生成及其水文地貌特征评价

数值地形图(DEM)是利用地理信息系统(GIS)进行流域水文模拟的基础, 其精度直接影响模拟结果在没有现成的数值地形图时, 应用人员往往利用传统的地形图来生成它. 本文分别采用Arc/Info地理信息系统软件提供的哈奇逊法和不规则三角网五次插值法, 对一个实验流域的高程取样点进行插值, 生成了4种不同的数值地形图, 从凹洼分布、流域界定、河网提取、地面坡度和地形指数、以及地面径流汇成等方面, 对它们的水文地貌精度进行了比较. 结果表明, 两种方法都能生成由高程点群所反映的地形, 然而由于哈奇逊法能够结合流域的河网结构及其具有物理基础的水文地貌加强法来处理凹洼问题, 因此大大地提高了其所生成的流域数值地形图水文地貌特征精度.     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

基于切削振动相关性识别刀具磨损状态的模型与实验

本文提出基于切削振动相关性识别刀具磨损状态的研究思想,建立了车削中刀杆双向横振动系统及其单输入双输出系统的数学模型。理论和实验均表明,刀杆双向横振动之加速度响应在固有基频处的相干函数与刀具磨损状态之间有很好的规律性,它反映了两者之间的本质机理,并提供了识别刀具磨损状态的新途径。     

Synthesis of diamond crystals and films using an oxygen-acetylene flame under atmosheric pressure

Diamond growth with rates up to 100 to 140 μm/hr was achieved using an oxygen-acetylene combustion spraying technique in an atmospheric environment. Investigations on the processing indicated that the gas flow ratio, substrate position, substrate temperature, temperature distribution, and substrate pretreatment were the most important factors affecting the growth of diamond crystals. Evaluation by means of X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and electron probe microanalysis showed that the synthesized diamond was nearly perfect in morphology, structure, and purity.