Mn/Ti-Zr复合氧化物催化苯甲酸甲酯选择性加氢

以硝酸锆和钛酸四丁酯为原料,采用共沉淀法制备Ti-Zr-O氧化物载体,采用浸渍法制备了Mn/Ti-Zr催化剂;采用XRD、N2物理吸附、H2-TPR、NH3-TPD和TG-DTA对Mn/Ti-Zr催化剂进行了表征,并考察了催化剂组成、结构和反应条件对苯甲酸甲酯（MB）加氢性能的影响,以及催化剂的长周期稳定性、失活和再生行为。结果表明：TiO2含量和Mn负载量分别为12% 和8% （二者均以Ti-Zr-O氧化物的质量为基准,下同）时制备的Mn/Ti-Zr催化剂性能最优,该催化剂在θ = 390 ℃, p = 1.0 MPa,n(H2)∶n(MB) = 9∶1和重时空速（WHSV）= 0.5 h-1的优化条件能够实现98.0% 的苯甲酸甲酯转化率和89.7%的苯甲醛和苯甲醇选择性;苯甲酸甲酯加氢反应的活性和选择性分别与Mn/Ti-Zr表面MnOx物种的氧化还原性和催化剂的酸性密切相关。此外,Mn/Ti-Zr催化剂具有良好的结构稳定性,在反应1000 h后仅因积碳而丧失11% 的活性,且轻微失活的催化剂可以通过焙烧恢复其初始活性和选择性。     

Facile Fabrication of Poly(vinyl alcohol)/Polyquaternium-10 (PVA/PQ-10) Anion Exchange Membrane with Semi-Interpenetrating Network

Anion exchange membranes (AEMs) are one of the core components of AEM fuel cells. A series of poly(vinyl alcohol)/polyquaternium-10 (PVA/PQ-10) AEMs with semi-interpenetrating networks (s-IPNs) are prepared by a simple solution-casting method using glutaraldehyde (GA) as a cross-linking agent. Subsequently, the prepared PVA/PQ-10 cross-linked membranes are characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, mechanical analysis, water uptake and swelling ratio tests, ion exchange capacity (IEC) tests, ionic conductivity measurements, and oxidative/alkaline stability tests. The effects of the mass ratio of PVA and PQ-10 and the amount of cross-linking agent GA on the performance of the PVA/PQ-10 cross-linked membranes are systematically explored. The results show that the cross-linked PVA/PQ-10 AEMs have high IEC and low water uptake and swelling ratio, and its maximum ionic conductivity can reach 79.37 mS cm^–1 at 80 °C. In addition, the PVA/PQ-10 cross-linked membrane has good oxidative and alkaline stability under optimal preparation conditions. These results may provide valuable insights toward more effective scheme designs and new, simple preparation methods for AEMs with s-IPN structures.     

Quantification of response time in poly(vinyl alcohol)–metal complex thermochromic polymeric systems

Thermochromic poly(vinyl alcohol) (PVA)‐based material was synthesized and an extensive study of its thermochromic behavior with respect to response time was carried out. It was observed that it is possible to manipulate the response time by keeping control over chemical and physical parameters. The response time, which is the most important property of a smart material, has in this case been found to be very much influenced by rate of heat transfer into the material. Different compositions of the thermochromic material and their corresponding response time with respect to rate of heat transfer were studied and correlated. First, a theoretical equation was derived and later on it was experimentally verified to quantify the response time in PVA–metal complex‐based thermochromic systems. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4832–4834, 2006     

Solvent-free oxidation of benzyl alcohol with oxygen using zeolite-supported Au and Au–Pd catalysts

The oxidation of benzyl alcohol to benzaldehyde has been investigated in the absence of solvent using zeolite-supported Au and Au–Pd catalysts. Three zeolites were investigated, ZSM-5, zeolite β and zeolite Y, and these were contrasted with the titanoslicalite TS-1 and TiO₂ as supports. For the Au catalysts the best results are obtained with zeolite β as the support and the conversions were comparable or better than those observed with TiO₂ in terms of turn over frequencies. However, the selectivities observed with the acidic zeolites were lower than the non-acidic TS-1 and TiO₂. This is due to the subsequent reaction of benzaldehyde via acid catalysed reactions to give benzyl benzoate and its dibenzyl acetal, and, in some cases dibenzylether. Initial catalysts were evaluated with a gold loading of 2 wt% and increasing this to 4 wt% showed the expected increase in activity, indicating that there is scope to improve the performance of these catalysts. The most active catalysts were prepared by impregnation and catalysts prepared by deposition precipitation were considerably less active. Introduction of Pd into the catalyst improved the activity without significantly affecting the selectivity.     

糖蜜酒精废液处理技术

介绍了甘蔗制糖生产中国内外糖蜜酒精废液的处理方法，对不同处理技术的特点进行了分析，认为焚烧法既能彻底处理糖密酒精废液，又能把废液处理和资源回收相结合，并概述了国内外废液焚烧技术。     

脂肪醇聚氧乙烯(3)醚低温浑浊原因的探讨

通过在AEO3中添加不同加成数的AEO进行低温浑浊试验，并分析比较AEO3低温分层后的上清液与下层浑浊物中AEO的分布，发现EO加成数在5以上的AEO是导致AEO3低温浑浊的原因之一。在AEO3及其上清液中分别添加不同质量分数的脂肪醇、水以及醋酸钠进行低温浑浊试验，发现脂肪醇、水分和醋酸钠不是造成AEO3低温浑浊的原因，但会使AEO3在低温下容易冻结。     

快速法测定AES中未硫酸化物的含量

讨论了一种快速测量AES中未硫酸化物的方法。首先将配制好的AES-乙醇溶液，通过离子交换树脂，然后收集、蒸馏、干燥得到的液体，称重后即可得到未硫酸化物的含量，采用该方法比国家标准节约2．5～3h的分析时间。     

3,5-二羟基苯甲醇的简便合成方法

以３，５ 二羟基苯甲酸为原料，经酯化、酰化、硼氢化锂还原等改进步骤合成了３，５ 二羟基苯甲醇，总收率达７５％，提供了一条较为简便的适合于工业化生产的合成方法。     

聚乙二醇对脂肪醇聚氧乙烯醚低温浑浊影响的研究

通过一系列低温浑浊试验考察了聚乙二醇含量与分子质量对脂肪醇聚氧乙烯醚(AEO3)低温浑浊的影响，并分析AEO3低温分层后的上清液和下层浑浊物中聚乙二醇的含量与分布，发现分子质量在600以上的聚乙二醇是影响AEO3低温浑浊的重要原因。     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.