核壳型聚苯乙烯/聚甲基丙烯酸甲酯复合乳液的制备

以过硫酸铵(APS)为引发剂,用种子乳液聚合方法,合成出以聚苯乙烯(PSt)为核, 聚甲基丙烯酸甲酯(PMMA)为壳的复合乳液。透射电子显微镜观察了核壳复合乳胶粒的形态,光散射粒径分布仪(PCS)测量胶乳粒径大小及其分布。最终成功地制得了核壳型PS/PMMA复合乳液,所得复合乳胶粒粒径大小在60～90nm左右,且单分散性较好。     

PVC及PMMA在CO_2环境中玻璃化转变特性的研究

对聚合物在CO2环境中的玻璃化转变特性进行了研究。利用蠕变柔量法,在自建的实验装置上,对聚氯乙烯和聚甲基丙烯酸甲酯在CO2环境中不同压力下的玻璃化转变温度进行了测定,并利用间接法测定了对应状态下聚合物中CO2的质量分数。结果表明,在CO2环境中2种材料的玻璃化转变温度显著降低。利用基于经典热力学与统计热力学理论构建的模型,对聚合物中不同的CO2质量分数对应的玻璃化转变温度值进行了计算,得到的计算结果与实验结果较吻合。     

GMA接枝SEBS及其对PA 6的改性及增容

用双螺杆反应挤出法将甲基丙烯酸缩水甘油酯(GMA)接枝到氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物(SEBS)上(即SEBS-g-GMA)，研究引发剂过氧化二异丙苯用量、活性单体GMA用量对接枝率的影响；通过双螺杆挤出、共混，制备聚酰胺(PA)6／SEBS-g-GMA、PA 6／SEBS-g-GMA／SEBS合金，研究SEBS-g-GMA对合金体系的相容性影响及增韧作用，探讨了合金体系的形态结构和力学性能。     

Surface morphology control of immiscible polymer-blend thin films

The effects of the molecular weights (molecular weight of polystyrene, M_w,PS, varying from 2.9 to 129 k) on the surface morphologies of spin-coated and annealed polystyrene/poly (methyl methacrylate) (PS/PMMA=50/50, w/w) blend films were investigated by atomic force microscopy and X-ray photoelectron spectroscopy. For the spin-coated films, when the M_w,PS varied from 2.9 to 129 k, three different kinds of surface morphologies (a nanophase-separated morphology, a PMMA cellular or network-like morphology whose meshes filled with PS, a sea-island like morphology) were observed and their formation mechanisms are discussed, respectively. Upon annealing, two different morphology-evolution processes were observed. It is found that a upper PS-rich phase layer is formed when M_w,PS<4 k, and this behavior is mainly attributed to the low interfacial tension between PS and PMMA component. When M_w,PS>4 k, the PS-rich phase forms droplets on top of the PMMA-rich phase layer which wets the SiO_x substrate. These results indicate that the surface morphology of the polymer blend films can be controlled by the polymer molecular weight and annealing conditions.     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

聚甲基丙烯酸甲酯／纳米SiO2复合粒子的制备与表征

采用甲基丙烯酸-3-甲氧基硅丙酯（MPs）对分散于甲基丙烯酸甲酯（MMA）中的纳米SiO2粒子进行偶联改性，得到了表面改性的纳米SiO2单体分散液，用原位悬浮聚合方法制备了不同SiO2含量的PMMA／纳米SiO2复合粒子。通过红外光谱、透射电镜、差示扫描量热分析和热重分析等方法对制备的纳米复合粒子进行了表征，结果表明，纳米SiO2粒子在PMMA中分散良好；MMA可通过与MPS的共聚而有效地接枝到SiO2粒子表面，当SiO2含量为6．6％（质量分数，下同）、MPS用量为0．06g／gSiO2时，其接枝率可达73．8％；同时，纳米SiO2的引入可提高PMMA的耐热性能，当Si02含量为14.7％时，其玻璃化转变温度和最大热分解速率时的温度分别提高了11．8℃和18．8℃。     

改性SBS胶粘剂的研制

以丙烯酸酯类混合单体对SBS热塑性弹性体在混合溶剂中接枝共聚，添加混合型增粘树脂，研制成接枝改性的SBS胶粘剂，具有较高的初粘力和终强度。探讨了单体比例、引发剂用量、反应温度、反应时间、增粘树脂对胶液性能的影响。     

The beneficial effect of small amount of water in the ambient temperature atom transfer radical homo and block co-polymerization of methacrylates

ATRP of several methacrylates viz. methyl methacrylate (MMA), ethyl methacrylate (EMA), n-butyl methacrylate (nBMA), t-butyl methacrylate (tBMA), benzyl methacrylate (BzMA) and (N,N-dimethylamino)ethyl methacrylate (DMAEMA) has been studied in neat as well as aqueous (up to 12 vol% water) acetone at 35 °C using CuCl/bipyridine (bpy) catalyst and ethyl 2-bromoisobutyrate as the initiator. Addition of water significantly enhances the rate of polymerization without losing control. Unlike CuCl/bpy the CuBr/bpy catalyst gives poor control which is attributed to the lower solubility and consequent heterogeneity in the latter case. Of the other ligands used with the CuCl catalyst viz. o-phenanthroline (o-phen), 1,1,4,7,7-pentamethyldiethylenetriamine (PMDETA), 1,1,4,7,10,10-hexamethyltriethylenetetramine (HMTETA), Me₆TREN only o-phen offers reasonably good control. The CuCl/bpy catalyst system has been used also in preparing some di- and tri-block copolymers with reasonably low polydispersity index (PDI) at ambient temperature (35 °C) using aqueous acetone as the solvent. The following block copolymers have been prepared PMMA-tBMA, PMMA-b-tBMA-b-MMA, PMMA-DMAEMA, by this method.     

回收PET共混物的非等温结晶和熔融行为

采用双螺杆挤出机制备了聚丙烯(PP)/回收聚对苯二甲酸乙二酯(r-PET)、r-PET/马来酸酐接枝PP(PP-g-MAH)和r-PET/甲基丙烯酸缩水甘油酯接枝PP(PP-g-GMA)共混物,并研究了共混物组成、熔融温度与时间以及降温速率对共混物非等温结晶与熔融行为的影响.结果表明,r-PET与PP共混,结晶温度均提高,这与组分间起到异相成核诱导结晶作用有关.r-PET结晶温度随PP-g-MAH用量增加而降低,但受PP-g-GMA用量影响较小;r-PET可提高PP-g-MAH结晶温度,但降低PP-g-GMA结晶温度.熔融温度提高,共混物中PP结晶温度和熔点均降低,r-PET熔融峰形和熔点取决于共混物的熔融温度及界面相互作用.     

Separation of kinetics and mass-transfer in a batch alkoxylation reaction

The quantitative aspects of the role of interfacial mass-transfer and reaction kinetics in ethoxylation of lauryl alcohol were examined in a batch recirculation reactor. The liquid droplets falling through a gas column were obtained by utilizing a recirculation loop and a set of spray nozzles. The CO₂/NaOH reaction was employed to characterize the interfacial area. The alkoxylation reaction was studied at temperatures between 124°C and 171°C, at catalyst levels between 0.09 and 0.50 weight percent and at ethylene oxide partial pressures between 68 kPa and 204 kPa. A model was developed which permits the prediction of reactor performance at various operating conditions. The mass-transfer during free fall dominates the interfacial mass-transfer and the contributions during the drop formation and coalescence stages are small. The rate of ethylene oxide (EO) addition to lauryl alcohol was constant during the batch run, indicating similar activity for the unreacted lauryl alcohol and the lauryl alcohol ethoxylated to varying extents. The rate of ethoxylation is first-order in both catalyst and ethylene oxide concentrations. The liquid-phase reaction kinetics and interfacial mass-transfer occur in series, with kinetics dominating the overall ethoxylation rate. As expected, an increasing role of mass transfer is observed at higher temperatures, and/or higher catalyst concentrations where the kinetic rate becomes significantly high. The intrinsic activation energy for the ethoxylation of lauryl alcohol is 55.2 kJ/mole.