Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

A new polymer electrolyte poly(acrylonitrile)-dimethylsulphoxide-salt for electrochemical capacitors

The PAN-DMSO-Et₄NBF₄ and PAN-DMSO-Et₄NTf (Tf is triflate ion) electrolytes were prepared as white, turbid foils with a thickness in the range of 0.1-0.5 mm, using the casting technique. Room temperature conductance of the electrolytes, detected from ac impedance experiments, was at the level of 8 and 14 mS cm⁻¹ for Et₄NBF₄ and Et₄NTf salts, respectively. The electrochemical stability window of approximately 2.6-2.8 V was estimated using a glassy carbon electrode. Temperature dependence of the conductivity is of the Arrhenius-type for both electrolytes, with an activation energy of approximately 34 kJ mol⁻¹. The double-layer capacitors built with these electrolytes, serving both as separators and activated carbon powder (ACP) binders, showed a specific capacity of 50 F g⁻¹ of carbon material. Capacitors were assembled by sandwiching the PAN-DMSO-salt electrolyte between two PAN-salt-DMSO-ACP-AB electrodes and pressing across the system; the resulting devices had a coin-like shape with 8 mm diameter and thickness between 2.0 and 2.5 mm.     

电磁发射兵器用电容器的选取

本文首先从理论上论述了膜电容器的储能密度与寿命之间的关系，对国际电容器制造水平和趋势进行了分析，提出采用干式金属化膜电容器作为储能元件。最后，根据电磁发射兵器整体寿命配合原则，提出高储能密度脉冲电容器的合理寿命指标。     

超级电容器在汽车启动中的应用

根据超级电容器的结构特性,介绍在汽车启动过程中如何利用超级电容器减小对车内其他电子设备的干扰,改善汽车的启动性能,延长蓄电池使用寿命.     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

Electro-organic synthesis without supporting electrolyte: Possibilities of solid polymer electrolyte technology

The application of ion exchange membranes as solid polymer electrolytes (SPE) in fuel cells is state-of-the-art. This technology needs no supporting electrolyte; consequently it can be applied for electro-organic syntheses in order to save process steps. In this case the process is not predetermined to a maximized energy efficiency so that the selection of the cell design, of the electrode materials and of the operating conditions can be focused on a high selectivity of the electrode reactions. The electro-osmotic stream, which is caused by the solvation shells of the ions during their migration through the membrane, and hence is a typical property of SPE technology, has a significant effect on the electrode reactions. It generates enhanced mass transfer at the electrodes, which is beneficial for reaction selectivity. It can be influenced by the choice of, and possibly by the preparation of, the membrane. An additional remarkable advantage of SPE technology is the exceptional long durability of oxide coated electrodes. By combination of several process engineering methods stable operation of SPE cells has been realized, even for examples of non-aqueous reaction systems. Experiments up to 6000 h duration and in cells of up to 250 cm² membrane area show the potential for industrial application.     

聚乙烯辐照接枝体系中添加金属盐对接技率的影响

采用辐照接枝的方法，在高密度聚乙烯(HDPE)上接枝丙烯酸(AA)和对苯乙烯磺酸钠(SSS)，从而削备出了一种含羧酸基团和磺酸基团的阳离子交换膜。详细研究了接枝体系中引入添加剂醋酸钠或氯化钠对接枝率的变化规律．实验表明，在预辐照接枝和共辐照接枝中，当AA接技PE或AA与SSS共同接枝PE时，强碱弱酸盐醋酸钠通过pH效应同离子效应对接枝率呈现复杂的影响，而中性盐氯化钠经离子对效应显著提高接枝率。     

液态金属离子源发射尖的制备工艺与技术

发射尖是液态金属离子源(LMIS)的关键部件之一，其性能的优劣直接影响到整个离子源的工作稳定性。通过对系统软件和硬件的设计，开发了一套发射尖自动腐蚀装置，该装置可以对发射尖腐蚀过程中的速度和深度以及腐蚀电压进行控制，实现发射尖腐蚀工艺的重复性、可靠性，从而为液态金属离子源以及聚焦离子束系统的研制、开发提供了一个有效的辅助工具。     

一种速度优化的流水线模数转换电容误差平均技术

无源电容误差平均技术是一种本质线性(Inherently Linear)的流水线模数转换电容失配校准技术,但其转换速度是传统技术的一半.为了提高速度,本文提出了一种改进的电容误差平均技术.该技术从减少一个转换周期所需的时钟相数目和减少每个时钟相的时间两个方面来优化速度.电路分析和MATLAB仿真表明,在两种典型的情况下,改进的技术能将速度提高52%(跨导放大器为开关电容共模反馈)和64%(跨导放大器为非开关电容共模反馈)以上.改进的技术更适用于高速高精度及连续工作的应用场合.     

Magnetic effects of direct ion implantation of Mn and Fe into p-GaN

In p-GaN implanted with Mn (3×10¹⁶ cm⁻² at 250 keV), the material after annealing shows ferromagnetic properties below 250 K. Cross-sectional transmission electron microscopy (TEM) revealed the presence of platelet structures with hexagonal symmetry. These regions are most likely Ga_xMn_1−xN, which produce the ferromagnetic contribution to the magnetization. In p-GaN implanted with Fe, the material after annealing showed ferromagnetic properties at temperatures that were dependent on the Fe dose, but were below 200 K in all cases. In these samples, TEM and diffraction analysis did not reveal any secondary phase formation. The results for the Fe implantation are similar to those reported for Fe doping during epitaxial growth of GaN.