Ethynedithiol‐based polyeneoligosulfides as active cathode materials for lithium‐sulfur batteries

Ethynedithiol‐based polyeneoligosulfides have been synthesized in 96% yield by the reaction of sodium acetylides (HC?CNa, NaC?CSNa) and elemental sulfur through the Na? C_sp bond in liquid ammonia with the following spontaneous polymerization of ethynedithiols (HSC?CSH) formed by the hydrolysis. The polyeneoligosulfides synthesized are brown powders (up to 77% sulfur content, mp 128–184°C), partially soluble in organic solvents. They are high‐resistance semiconductors (10^?13 to 10^?14 S cm^?1), possess paramagnetic (10¹⁷ to 10¹⁸ spin g^?1) and redox properties. The oligosulfides obtained, being redox systems capable of reversible redox processes, provide high values of discharge capacity (345–720 mA h g^?1) of rechargeable lithium‐sulfur batteries. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Effect of Li+ ions on structure,properties, and actuation of cellulose electro‐active paper actuator

We have reported an electro‐active paper actuator from regenerated cellulose. After dissolving cellulose fibers with a solution of lithium chloride in N,N‐dimethylacetamide, cellulose was regenerated by combining distillation of cellulose solution along with washing with the mixture of deionized water, isopropyl alcohol, and running water. However, the effect of Li⁺ ions on structure, properties, and the actuation behavior of the actuator was not studied. This article describes the changes in these parameters when the Li⁺ ions are removed by subjecting it to different running water exposure time. The structure and properties of cellulose electro‐active paper and its actuation behavior were studied. As Li⁺ ions content reduced from 4354.17 to 10.26 ppm by increasing the exposure time of running water, crystallinity, Young's modulus, and bending displacement decreased. Details about the investigation have been explained. This elimination of ions is important to increase the piezoelectric effect in EAPap by decreasing the ion migration effect. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Investigation of the Correlation between Texture and Microstructure on a Submicrometer Scale in the TEM

In recent years the investigation of local texture and microstructure by analysis of electron backscatter diffraction patterns (EBSP) in the SEM has become a very powerful and popular method. With the introduction of SEM with field emission guns (FEG) the spatial resolution of EBSP measurements could be enhanced from 500 nm with a tungsten emitter to better than 50 nm. This evolution of SEM techniques raises the question whether transmission electron microscopy (TEM) still has fields of application in texture research. The present article answers this question with a clear “yes” and presents three examples of investigations where TEM is indispensable. The three examples comprise the investigation of the correlation between dislocation structure and deformation texture, a study on nucleation mechanisms of recrystallization in highly deformed metals and the investigation of microtexture and microstructure in nanocrystalline materials. Together with the presentation of these cases some of the necessary measurement techniques are described briefly. It is shown that TEM has to be applied when highest spatial resolution of orientation determination and imaging and high accuracy of orientation determination are to be reached, when the three‐dimensional and quantitative characterization of lattice defects is required or when materials with a high density of lattice defects are to be investigated.     

垂直定向液晶光阀及光电特性的研究

系统地讨论了排列相畸变模式液晶光阀结构，原理和制作，结合实际测试对其等效电路和电学匹配进行了分析，详细讨论了它的光电特性及相互关系，实测的液晶垂直排列方式工作的液晶光阀性能指标为，分辨率大于５０ｌｐ／ｍｍ，白光输入灵敏度为６．７７μＷ／ｃｍ＾２，响应时间为２００ｍｓ／３００ｍｓ，白光输出对比度为２００：１。     

高温超高压处理HDPE的WAXD及FT－IR研究

用ＷＡＸＤ和ＦＴ－ＩＲ对高温超高压处理前后的ＨＤＰＥ进行了研究。发现经５．０ＧＰａ的高压处理或２００℃下４．０ＧＰａ的高压同时处理后的ＨＤＰＥ分子链的化学结构未发生变化。ＨＤＰＥ晶体中（２００）面与（１１０）面衍射峰的峰高比（γ）随着压力的升高而增大，表明ＨＤＰＥ分子链在超高压作用下发生了取向排列，且升高温度更有利于这种取向排列，但当压力增大至５．０ＧＰａ及温度升高至２００℃时，γ反而大幅度下降。     

较大直径、低位错锑化铟单晶的研制

本文简要介绍了用ＴＤＫ－３６单晶炉拉制的较大直径（φ＝２５ｍｍ）、低位错（＜１００ｃｍ￣（－２））的锑化铟单晶的理论和实践。通过对晶体生长室内温场，特别是内外坩埚尺寸的调整及对循环水流量的控制，成功地拉制出较大直径、低位错的锑化铟单晶。     

单液晶光阀彩色大屏幕投影显示

设计一电路,将彩色图象信息编码到黑白CRT的亮度之中,并将其写入液晶光阀,用白光读出,当编码合适时,读出的象颜色可与原图像一致。本文讨论了这一技术原理并进行了单液晶光阀彩色大屏幕投影的实验验证。     

聚氧乙烯 - 聚氧丙烯 - 聚苯乙烯多嵌段聚合物的力学和导电性能研究

研究了聚苯乙烯含量对聚氧乙烯－聚氧丙烯－聚苯乙烯多嵌段聚合物的力学性能及其与ＬｉＣｌＯ４络合物的离子导电性能的影响；并以电导率较高的络合物为电解质，Ｎａ１＋ｘＶ３Ｏ８复合物和Ｌｉ片分别为正、负极组装了薄型锂电池并测定其放电性能。     

Thermal properties and crystalline structure of liquid crystalline poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate)

Thermal properties and crystalline structure of liquid crystalline (LC) poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate) [copoly(ET/CPT)] were investigated using differential scanning calorimetry (DSC), thermogravimetry (TGA), limiting oxygen index (LOI) measurement, electron dispersive X‐ray analysis (EDX), X‐ray diffractometry, and infrared spectrometry (IR). The thermal transition temperatures of copoly(ET/CPT) were changed with the composition. Copoly(ET/CPT) showed two thermal decomposition steps and the residues at 700°C and LOI values of copoly(ET/CPT) were almost proportional to its chlorine content. The activation energy of thermal decomposition of LC units was very low compared to that of poly(ethylene terephthalate)(PET) units. Crystal structure of copoly(ET/CPT) (20/80) was of triclinic system with the lattice constants of a = 9.98 A?, b = 8.78 A?, c = 12.93 A?, α = 97.4°, β = 96.1°, and γ = 90.8°, which is very close to that of poly(chloro‐p‐phenylene terephthlate) (PCPT) with the lattice constants of a = 9.51 A?, b = 8.61 A?, c = 12.73 A?, α = 96.8°, β = 95.4°, and γ = 90.8°. When copoly(ET/CPT)(50/50) was annealed at 220°C in vacuum, crystallization induced sequential reordering (CISR) was not observed but the heat of fusion was slightly increased due to the increase of the trans isomer content in PET units. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1286–1294, 2002; DOI 10.1002/app.10451